| About |
|---|
| PRE-ELEC® ESD 7120 is a static dissipative thermoplastic compound based on ABS. The dissipative property is permanent and built into the polymer chain. PRE-ELEC® ESD 7120 has been developed for injection moulding and for the extrusion of thermoformable mono- or multi-layer sheet. The products made out of PRE-ELEC® ESD 7120 are transparent, washable, reusable and recyclable. Surface resistance values of 1e8 ohms (EOS/ESD S11.11-1993, IEC 61340-5-1) can be achieved with optimum processing parameters. Typical applications include trays, tote bins, crates and technical parts which give permanent ESD protection for the electronics, medical, pharmaceutical and paper handling industries. PRE-ELEC® ESD 7120 can also be used as covers and lids as it is transparent.&& |
| Product Description | |
|---|---|
| Supplier | Premix Oy |
| Generic | ABS |
| Material Status | Commercial: Active |
| Features | Good Clarity,Renewable resources |
| Availabilitys | North America,Latin America,Asia Pacific,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.08 | g/cm³ | ASTM D792 |
| Density | 1.07 | g/cm³ | ISO 1183 |
| Melt Flow Rate | |||
| 200℃，5.0kg | 7.0 | g/10min | ISO 1133 |
| Shrinkage rate | |||
| MD | 0.50 to 0.70 | % | ASTM D955 |
| MD | 0.50 to 0.70 | % | ISO 294-4 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | |||
| Shaw’s D | 73 | ISO 868 | |
| Shaw’s D | 73 | ASTM D2240 | |
| tensile strength | 22.8 | MPa | ASTM D638 |
| yield | 34.0 | MPa | ISO 527-2 |
| yield | 33.8 | MPa | ASTM D638 |
| 4 mm | 23.0 | MPa | ISO 527-2 |
| Tensile strain | |||
| Fracture, 4 mm | 25 | % | ISO 527-2 |
| fracture | 25 | % | ASTM D638 |
| yield | 6.0 | % | ASTM D638 |
| yield | 6.0 | % | ISO 527-2 |
| Bending modulus | |||
| 4 mm | 1600 | MPa | ISO 178 |
| 4 mm | 1590 | MPa | ASTM D790 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | |||
| 23℃，4.00 mm，Area | 2.31 | kJ/m² | ASTM D256 |
| 23℃ | 6.0 | kJ/m² | ISO 180 |
| Notched impact strength of cantilever beam | |||
| Area，23℃，4.00 mm | 15.8 | kJ/m² | ASTM D256 |
| 23℃ | 40 | kJ/m² | ISO 180 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed | 70.0 | ℃ | ISO 75-2/Af |
| 1.8 MPa, unannealed | 70.0 | ℃ | ASTM D648-A |
| 0.45 MPa, unannealed | 84.0 | ℃ | ISO 75-2/Bf |
| 0.45 MPa, unannealed | 83.9 | ℃ | ASTM D648-B |
| Vicat Softening Temp | |||
| — | 101 | ℃ | ASTM D1525 3 |
| — | 87.2 | ℃ | ASTM D1525 4 |
| Vicat Softening Temp | |||
| A50 | 101 | ℃ | ISO 306/A50 |
| B50 | 87.0 | ℃ | ISO 306 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Surface resistivity | < 1.0E+10 | ohms | ESD STM11.11 |
| Surface resistivity | < 1.0E+10 | ohms | IEC 61340-2-3 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Extrusion | Nominal value | Unit | Test method |
| Drying temperature | 70 to 80 | °C | |
| Drying time | 3.0 to 4.0 | hr | |
| Processing (melt) temperature | 180 to 210 | °C | |
| Mold temperature | 30 to 70 | °C | |
| Injection pressure | 75.2 to 120 | MPa | |
| Injection speed | Moderate | ||
| Drying temperature | 70 to 80 | °C | |
| Drying time | 3.0 to 4.0 | hr | |
| Barrel 1 zone temperature | 170 | °C | |
| Barrel 2 zone temperature | 190 | °C | |
| Barrel 3 zone temperature | 190 | °C | |
| Barrel 4 zone temperature | 190 | °C | |
| Barrel 5 zone temperature | 190 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 4 mm thickness |
| 3. Rate A (50°C/h), Loading 2 (50 N) |
| 4. Rate B (120°C/h), Loading 2 (50 N) |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |