Prime PE HMWPE 1000 SR

About
Prime HMWPE SR is a coextruded product consisting of a cap layer on both sides of the sheet to provide a skid resistant surface. Applications: Prime HMWPE SR is designed for pallets, dunnage trays, truck bed liners or any other parts that require a high COF. Processing: Prime HMWPE 1000 SR is extruded and thermoformed using the same conditions as HMWPE. However, an A-B-A feed block is required for extruding the 3-layer sheet. Finishing: Cutting and machining of this product may be done by sawing, drilling, grinding, sanding, punching, die cutting and routing. The material may be bonded with mechanical fasteners and sonic welding. Please contact your Primex Plastics representative for more information on finishing, fabricating, or the thermoforming process. Colors, Textures and Capabilities: Prime HMWPE SR can be color matched to meet your specific requirements. Available textures include H/C, Levant II, Seville, RM and Levant III. This product is offered in .100 to .400 in. total thickness and up to 160″ wide.&&

About

Prime HMWPE SR is a coextruded product consisting of a cap layer on both sides of the sheet to provide a skid resistant surface. Applications: Prime HMWPE SR is designed for pallets, dunnage trays, truck bed liners or any other parts that require a high COF. Processing: Prime HMWPE 1000 SR is extruded and thermoformed using the same conditions as HMWPE. However, an A-B-A feed block is required for extruding the 3-layer sheet. Finishing: Cutting and machining of this product may be done by sawing, drilling, grinding, sanding, punching, die cutting and routing. The material may be bonded with mechanical fasteners and sonic welding. Please contact your Primex Plastics representative for more information on finishing, fabricating, or the thermoforming process. Colors, Textures and Capabilities: Prime HMWPE SR can be color matched to meet your specific requirements. Available textures include H/C, Levant II, Seville, RM and Levant III. This product is offered in .100 to .400 in. total thickness and up to 160″ wide.&&

Product Description
Generic	HMW-HDPE
Material Status	Commercial: Active
Features	High Friction,Skid Resistant,High impact resistance,Ultra high molecular weight,Ultrasonic soldering,low-temperature impact resistance,High ESCR,Agglomerability
Availabilitys	North America,Europe
Process Methods	Extrusion

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	0.944	g/cm³	ASTM D792
Melt Flow Rate
190℃，2.16kg	12	g/10min	ASTM D1238
ESCR(Environmental Stress Cracking Resistance)
F50	> 600	hr	ASTM D1693A

MECHANICAL	Nominal value	Unit	Test method
tensile strength
yield	20.7	MPa	ASTM D638
Bending modulus	1170	MPa	ASTM D790
friction coefficient	0.44		ASTM D3028

IMPACT	Nominal value	Unit	Test method
Impact strength of cantilever beam notch
23℃	270	J/m	ASTM D256-A

THERMAL	Nominal value	Unit	Test method
Hot deformation temperature
0.45 MPa, unannealed	60.0	℃	ASTM D648
Vicat Softening Temp	116	℃	ASTM D1525
Melting temperature	130	℃
Linear coefficient of thermal expansion
MD	1.3E-4	1/℃	ASTM D696

Notes
1. Typical properties: these are not to be construed as specifications.
2. HLMI
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.