Propylux® HS2

About
Through process improvement and advanced engineering, Westlake Plastics introduces the next generation of heat-stabilized polypropylene. Propylux HS2 is produced from a FDA and USP Class VI approved homopolymer resin, and exhibits better heat and dimensional stability over Propylux HS. Recommended sterilization techniques for Propylux HS2 include steam autoclaving and cold sterilization. Advantages: Excellent Chemical Resistance Laser Markable Lot controlled and traceable Low Moisture Absorption FDA Resin Superior Dimensional Stability Applications: Provisional Trials Cranio-maxillofacial trays Sterilization tray components&&

About

Through process improvement and advanced engineering, Westlake Plastics introduces the next generation of heat-stabilized polypropylene. Propylux HS2 is produced from a FDA and USP Class VI approved homopolymer resin, and exhibits better heat and dimensional stability over Propylux HS. Recommended sterilization techniques for Propylux HS2 include steam autoclaving and cold sterilization. Advantages: Excellent Chemical Resistance Laser Markable Lot controlled and traceable Low Moisture Absorption FDA Resin Superior Dimensional Stability Applications: Provisional Trials Cranio-maxillofacial trays Sterilization tray components&&

Product Description
Supplier	Westlake Plastics
Generic	PP not specified
Material Status	Commercial: Active
Features	Good Dimensional Stability,Steam sterilized,High pressure disinfection,Solvent resistance,High pressure heat resistance,Laser engraving,Resistance to the steam,Low moisture absorption,Heat Stabilized,HB
Availabilitys	North America

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	0.920	g/cm³	ASTM D792
Water absorption rate
24hr	0.010	%	ASTM D570

IMPACT	Nominal value	Unit	Test method
Impact strength of cantilever beam notch	160	J/m	ASTM D256
Notched impact strength of cantilever beam	无断裂		ASTM D256

THERMAL	Nominal value	Unit	Test method
Hot deformation temperature			ASTM D648
0.45 MPa, unannealed	154	℃	ASTM D648
1.8 MPa, unannealed	93.9	℃	ASTM D648
Linear coefficient of thermal expansion
MD	7.9E-5	1/℃	ASTM D696

FLAME CHARACTERISTICS	Nominal value	Unit	Test method
Flame retardant level	HB		UL 94

MECHANICAL	Nominal value	Unit	Test method
Rockwell hardness
R-level	100		ASTM D785
Tensile modulus	2200	MPa	ASTM D638
tensile strength			ASTM D638
yield	34.3	MPa	ASTM D638
fracture	29.2	MPa	ASTM D638
Tensile strain			ASTM D638
yield	5.0	%	ASTM D638
fracture	70	%	ASTM D638
Bending modulus	2270	MPa	ASTM D790
bending strength	64.6	MPa	ASTM D790
compressive strength	47.4	MPa	ASTM D695

Notes
1. Typical properties: these are not to be construed as specifications.
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

1. Typical properties: these are not to be construed as specifications.

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.