ProtoTherm 12110

About
DSM’s Somos® ProtoTherm 12110 is a liquid photopolymer that produces strong, high-temperature tolerant, water-resistant parts. Parts created with Somos® ProtoTherm 12110 have a cherry-red appearance which turns to an orange-red color after thermal treatment. Applications Somos® ProtoTherm 12110 differentiates itself from other high temperature stereolithography materials by increasing in tensile strength and maintaining decent elongation at break after thermal treatment. This makes the material ideal for many applications in the automotive and aerospace markets where strong parts that can resist high temperatures are needed.&&

About

DSM’s Somos® ProtoTherm 12110 is a liquid photopolymer that produces strong, high-temperature tolerant, water-resistant parts. Parts created with Somos® ProtoTherm 12110 have a cherry-red appearance which turns to an orange-red color after thermal treatment. Applications Somos® ProtoTherm 12110 differentiates itself from other high temperature stereolithography materials by increasing in tensile strength and maintaining decent elongation at break after thermal treatment. This makes the material ideal for many applications in the automotive and aerospace markets where strong parts that can resist high temperatures are needed.&&

Product Description
Supplier	DSM
Generic	3D打印材料
Material Status	Commercial: Active
Features	Good Rigidity,Low or no water absorption,High Heat Resistance,Moisture resistance,Good Tensile Strength
Availabilitys	North America,Asia Pacific,Europe

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	1.15	g/cm³
Water absorption rate
balance	0.28	%	ASTM D570
viscosity
30℃	0.41	Pa·s

IMPACT	Nominal value	Unit	Test method
Impact strength of cantilever beam notch	12	J/m	ASTM D256-A

THERMAL	Nominal value	Unit	Test method
Hot deformation temperature			ASTM D648
0.45 MPa, unannealed	52.9	℃	ASTM D648
1.8 MPa, unannealed	48.0	℃	ASTM D648
Glass transition temperature	59.3	℃	ASTM E1545
Linear coefficient of thermal expansion
MD			ASTM E831
-40 to 0 ℃	5.8E-5	cm/cm/℃	ASTM E831
0 to 50 ℃	8.6E-5	cm/cm/℃	ASTM E831
50 to 100 ℃	1.2E-4	cm/cm/℃	ASTM E831
100 to 150 ℃	1.4E-4	cm/cm/℃	ASTM E831

Electrical performance	Nominal value	Unit	Test method
Dielectric strength	17	kV/mm	ASTM D149
Dielectric constant			ASTM D150
60 Hz	3.54		ASTM D150
1 kHz	3.52		ASTM D150
1 MHz	3.39		ASTM D150

Supplementary information	Nominal value	Unit	Test method
Critical Exposure	12.2	mJ/cm²
Penetration depth	139.7	µm

MECHANICAL	Nominal value	Unit	Test method
Shore hardness
Shaw’s D	85		ASTM D2240
Tensile modulus	3430	MPa	ASTM D638
tensile strength	57.6	MPa	ASTM D638
Tensile strain
fracture	5.0	%	ASTM D638
Bending modulus	3350	MPa	ASTM D790
bending strength	108	MPa	ASTM D790

Notes
1. Typical properties: these are not to be construed as specifications.
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

1. Typical properties: these are not to be construed as specifications.

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.