| About |
|---|
| Quadrant EPP CESTIDUR® PE-UHMW是一种超高分子量聚乙烯产品,。 它,在欧洲有供货。 典型应用领域为:工程/工业配件。 特性包括: 阻燃/额定火焰 耐磨 良好的韧性 高分子量&& |
| Product Description | |
|---|---|
| Supplier | Quadrant |
| Generic | Ultra-high molecular weight polyethylene |
| Material Status | Commercial: Active |
| Features | Good flexibility,Ultra high molecular weight,Good wear resistance,HB |
| Availabilitys | Europe |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 0.930 | g/cm³ | ISO 1183 |
| Water absorption rate | |||
| Saturation, 23 ℃, 1.00 mm | 0.010 | % | ISO 62 |
| molecular weight | 6000000 | g/mol | |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | |||
| — | > 120 | kJ/m² | Internal Method |
| Local fracture | 110 | kJ/m² | ISO 179/1eA |
| Charpy Unnotch Impact strength | 无断裂 | ISO 179/1eU |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed | 42.0 | ℃ | ISO 75-2/A |
| Continuous use temperature | |||
| — | 80.0 | ℃ | |
| — | 120 | ℃ | |
| Vicat Softening Temp | 80.0 | ℃ | ISO 306/B |
| Melting temperature | 130 to 135 | ℃ | ISO 11357-3 |
| Linear coefficient of thermal expansion | |||
| MD：23~100℃ | 2.0E-4 | 1/℃ | |
| Thermal conductivity coefficient | |||
| 23℃ | 0.40 | W/m/K | |
| Operating temperature | |||
| minimum | -200 | ℃ |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Surface resistivity | > 1.0E+13 | ohms | IEC 60093 |
| Volume resistivity | > 1.0E+14 | ohms·cm | IEC 60093 |
| Dielectric strength | |||
| 1 mm in oil | 45 | kV/mm | IEC 60243-1 |
| Relative permittivity | IEC 60250 | ||
| 100 Hz | 2.10 | IEC 60250 | |
| 1 MHz | 3.00 | IEC 60250 | |
| Dissipation factor | IEC 60250 | ||
| 100 Hz | 4.0E-4 | IEC 60250 | |
| 1 MHz | 1.0E-3 | IEC 60250 | |
| Compared to the leakage tracing index | 600 | V | IEC 60112 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| 1.60 mm | HB | UL 94 | |
| Extreme oxygen index | < 20 | % | ISO 4589-2 |
| Supplementary information | Nominal value | Unit | Test method |
|---|---|---|---|
| Relative Weight Loss | Internal Method | ||
| — | 90.0 | Internal Method |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | ISO 868 | ||
| Shore D, 3 seconds | 62 | ISO 868 | |
| Shore D, 15 seconds | 60 | ISO 868 | |
| Ball hardness | 35.0 | MPa | ISO 2039-1 |
| Tensile modulus | 710 | MPa | ISO 527-2/1B/1 |
| tensile strength | |||
| yield | 19.0 | MPa | ISO 527-2/1B/50 |
| Tensile strain | |||
| yield | 15 | % | ISO 527-2/1B/50 |
| Nominal tensile fracture strain | > 50 | % | ISO 527-2/1B/50 |
| compressive strength | ISO 604/1 | ||
| 5% strain | 13.5 | MPa | ISO 604/1 |
| 2% strain | 7.50 | MPa | ISO 604/1 |
| 1% strain | 4.00 | MPa | ISO 604/1 |
| Notes |
|---|
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |