| About |
|---|
| Quadrant EPP Ertalyte® is a Polyethylene Terephthalate (PET) product. It can be processed by extrusion and is available in Latin America or North America. Typical application: Food Contact Applications. Characteristics include: Flame Rated Crystalline&& |
| Product Description | |
|---|---|
| Supplier | Quadrant |
| Material Status | Commercial: Active |
| Features | Good Dimensional Stability,Good wear resistance |
| Availabilitys | Europe |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.39 | g/cm³ | ISO 1183-1 |
| Water absorption rate | |||
| 23℃，24h | 6 | mg | ISO 62 |
| 23℃，24h | 0.07 | % | ISO 62 |
| 23℃，96h | 13 | mg | ISO 62 |
| 23℃，96h | 0.16 | % | ISO 62 |
| Equilibrium, 23 ℃, 50% RH | 0.25 | % | |
| Saturation, 23 ℃ | 0.50 | % | |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy impact strength | |||
| 23 ℃, no notch | 50 | KJ/m² | ISO 179-1/1eU |
| 23 ℃, notch | 2 | KJ/m² | ISO 179-1/1eA |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa | 80 | ℃ | ISO 75-1/-2 |
| melting point | |||
| DSC，10℃/min | 245 | ℃ | ISO 11357-1/-3 |
| Linear coefficient of thermal expansion | |||
| 23 – 60℃ | 6.0E-5 | m/（m·K） | |
| 23 – 100℃ | 8.0E-5 | m/（m·K） | |
| Thermal conductivity coefficient | |||
| 23℃ | 0.29 | W/m/K | |
| Maximum operating temperature | |||
| short time | 160 | ℃ | |
| Continuous, 5000h | 115 | °C | |
| Continuous, 20000 hours | 100 | °C | |
| Minimum operating temperature | -20 | °C |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Surface resistivity | |||
| 23℃ | ＞1.0E+13 | ohm/sq | IEC 60093 |
| Volume resistivity | |||
| 23℃ | ＞1.0E+14 | ohms·cm | IEC 60093 |
| Dielectric strength | |||
| 1 mm in oil | 22 | kV/mm | IEC 60243-1 |
| Dissipation factor | |||
| 23℃，100Hz | 0.001 | IEC 60250 | |
| 23℃，1MHz | 0.014 | IEC 60250 | |
| Relative permittivity | |||
| 23℃，100Hz | 3.4 | IEC 60250 | |
| 23℃，1MHz | 3.2 | IEC 60250 | |
| Compared to the leakage tracing index | 600 | IEC 60112 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | |||
| 3.0 mm | HB | UL 94 | |
| 6.0 mm | HB | UL 94 | |
| Oxygen index | 25 | % | ISO 4589-1/-2 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile stress | |||
| 23 ℃, 50 mm/min, yield | 90 | MPa | ISO 527-1/-2 |
| tensile strength | |||
| 23℃，50 mm/min | 90 | MPa | ISO 527-1/-2 |
| Tensile strain | |||
| 23 ℃, 50 mm/min, yield | 4 | % | ISO 527-1/-2 |
| 23 ℃, 50 mm/min, fracture | 15 | % | ISO 527-1/-2 |
| Tensile modulus | |||
| 23℃，1 mm/min | 3500 | MPa | ISO 527-1/-2 |
| compressive strength | |||
| 23 ℃, 1% strain | 33 | MPa | ISO 604 |
| 23 ℃, 2% strain | 64 | MPa | ISO 604 |
| 23 ℃, 5% strain | 107 | MPa | ISO 604 |
| Ball hardness | |||
| 10.0 mm | 170 | N/mm² | ISO 2039-1 |
| Rockwell hardness | |||
| M-grade, 10.00 mm | 96 | ISO 2039-2 |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Method A (Short-Time) |
| 3. 1-10, 1=Easier to Machine |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |