| About |
|---|
| Quadrant EPP TIVAR® DrySlide is an Ultra High Molecular Weight Polyethylene product. It is available in Latin America or North America. Characteristics include: Flame Rated Conductive Lubricated UV Stabilized&& |
| Product Description | |
|---|---|
| Supplier | Quadrant |
| Generic | Ultra-high molecular weight polyethylene |
| Material Status | Commercial: Active |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 0.935 | g/cm³ | ISO 1183-1 |
| Water absorption rate | |||
| 23 ℃, saturated | < 0.10 | % | ASTM D570 |
| Average molar mass | 9.0E+6 | g/mol | |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy impact strength | |||
| No gap | 无断裂 | KJ/m² | ISO 179-1/1eU |
| Gap | 100P | KJ/m² | ISO 179-1/1eA |
| Gap (two 14 ° notches) | 130 | KJ/m² | ISO 11542-2 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| melting point | |||
| DSC，10℃/min | 135 | ℃ | ISO 11357-1/-3 |
| Maximum operating temperature | |||
| short time | 120 | ℃ | |
| Continuous, 20000 hours | 80 | °C | |
| Minimum operating temperature | -150 | °C | |
| Linear coefficient of thermal expansion | |||
| 23 – 100℃ | 2.0E-4 | m/(m.K) | |
| Thermal conductivity coefficient | |||
| 23℃ | 0.40 | W/m/K | |
| Vicat Softening Temp | 80 | ℃ | ISO 306 |
| Hot deformation temperature | |||
| 1.8MPa | 42 | ℃ | ISO 75-1/-2 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Surface resistivity | |||
| 23℃ | ＜1.0E+8 | ohm | IEC 60093 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| UL flame retardant rating | |||
| 6.00 mm | HB | UL 94 | |
| Oxygen index | ＜20 | % | ISO 4589-1/-2 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile stress | |||
| 23 ℃, 50 mm/min, yield | 18 | MPa | ISO 527-1/-2 |
| Tensile strain | |||
| 23 ℃, 50 mm/min, yield | 20 | % | ISO 527-1/-2 |
| 23 ℃, 50 mm/min, fracture | ＞50 | % | ISO 527-1/-2 |
| Tensile modulus | |||
| 23℃，1 mm/min | 650 | MPa | ISO 527-1/-2 |
| compressive strength | |||
| 23 ℃, 1% strain | 6 | MPa | ISO 604 |
| 23 ℃, 2% strain | 10 | MPa | ISO 604 |
| 23 ℃, 5% strain | 16 | MPa | ISO 604 |
| Ball hardness | |||
| 10.0 mm | 32 | N/mm² | ISO 2039-1 |
| Relative volume loss | |||
| “Sand/Water Mud” Wear Test | 85 | ISO 15527 | |
| Shore hardness | |||
| D-grade, 10.00 mm | 59 | ISO 868 |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 1-10, 1=Easier to Machine |
| 3. 1018 Steel = 100 |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |