| About |
|---|
| Quadrant EPP TIVAR® MD UHMW-PE is an Ultra High Molecular Weight Polyethylene product. It is available in Latin America or North America. Typical application: Food Contact Applications. Characteristics include: Flame Rated Chemical Resistant Corrosion Resistant Low Moisture Absorption Non-Toxic&& |
| Product Description | |
|---|---|
| Supplier | Quadrant |
| Generic | Ultra-high molecular weight polyethylene |
| Material Status | Commercial: Active |
| Features | High impact resistance,Good wear resistance,Corrosion Resistant,Good flexibility |
| Availabilitys | Europe |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 0.995 | g/cm³ | ISO 1183-1 |
| Water absorption rate | |||
| 23 ℃, saturated | < 0.10 | % | |
| Average molar mass | 9.0E+6 | g/mol | |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy impact strength | |||
| No gap | 无断裂 | KJ/m² | ISO 179-1/1eU |
| Gap | 90P | KJ/m² | ISO 179-1/1eA |
| Gap (two 14 ° notches) | 105 | KJ/m² | ISO 11542-2 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| melting point | |||
| DSC，10℃/min | 135 | ℃ | ISO 11357-1/-3 |
| Thermal conductivity coefficient | |||
| 23℃ | 0.40 | W/m/K | |
| Linear coefficient of thermal expansion | |||
| 23 – 100℃ | 2.0E-4 | m/（m·K） | |
| Maximum operating temperature | |||
| short time | 120 | ℃ | |
| Continuous, 20000 hours | 80 | °C | |
| Minimum operating temperature | -150 | °C | |
| Hot deformation temperature | |||
| 1.8MPa | 42 | ℃ | ISO 75-1/-2 |
| Vicat Softening Temp | 82 | ℃ | ISO 306 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Surface resistivity | |||
| 23℃ | ＞1.0E+12 | ohm | IEC 60093 |
| Volume resistivity | |||
| 23℃ | ＞1.0E+14 | ohm·cm | IEC 60093 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| UL flame retardant rating | |||
| 6.00 mm | HB | UL 94 | |
| Oxygen index | ＜20 | % | ISO 4589-1/-2 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile stress | |||
| 23 ℃, 50 mm/min, yield | 19 | MPa | ISO 527-1/-2 |
| Shore hardness | |||
| D-grade, 10.00 mm | 62 | ISO 868 | |
| Tensile strain | |||
| 23 ℃, 50 mm/min, yield | 15 | % | ISO 527-1/-2 |
| 23 ℃, 50 mm/min, fracture | ＞50 | % | ISO 527-1/-2 |
| Tensile modulus | |||
| 23℃，1 mm/min | 775 | MPa | ISO 527-1/-2 |
| compressive strength | |||
| 23 ℃, 1% strain | 7 | MPa | ISO 604 |
| 23 ℃, 2% strain | 11.5 | MPa | ISO 604 |
| 23 ℃, 5% strain | 18 | MPa | ISO 604 |
| Ball hardness | |||
| 10.0 mm | 30 | N/mm² | ISO 2039-1 |
| Relative volume loss | |||
| “Sand/Water Mud” Wear Test | 75 | ISO 15527 |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 1018 Steel = 100 |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |