| About |
|---|
| Radel® R-5100 is an opaque, general purpose polyphenylsulfone (PPSU) for injection molding, that offers exceptional hydrolytic stability, and toughness superior to other commercially-available, high-temperature engineering resins. This resin also offers a high deflection temperature and outstanding resistance to environmental stress cracking. Radel® polymers are inherently flame retardant, provide excellent thermal stability and possess good electrical properties. Black: Radel® R-5100 BK937 Bone: Radel® R-5100 NT15 Grey: Radel® R-5100 GY1137 Grey: Radel® R-5100 GY1037 Grey: Radel® R-5100 GY874 Red: Radel® R-5100 RD1018 Orange: Radel® R-5100 OR1145 Yellow: Radel® R-5100 YL1337 Green: Radel® R-5100 GN1007 Blue: Radel® R-5100 BU1027 Violet: Radel® R-5100 VT2582 Brown: Radel® R-5100 BN1164&& |
| Product Description | |
|---|---|
| Supplier | Solvay |
| Generic | PPSU |
| Material Status | Commercial: Active |
| Features | Alkali resistant,Good disinfection,Steam sterilized,Hydrolysis stability,Gamma radiation,E-beam disinfection,Biocompatible,Flame Characteristics,High pressure disinfection,Acidproof,High Heat Resistance,Radioactive,Ultra high toughness,Radiation disinfection,Solvent resistance,Resistance to the steam,Heat Stabilized,High ESCR,Ethylene oxide disinfection,Heat sterilization,V-0 |
| Availabilitys | North America,Latin America,Asia Pacific,Europe |
| Process Methods | Profile extrusion |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.30 | g/cm³ | ASTM D792 |
| Melt Flow Rate | 14 to 20 | g/10min | ASTM D1238 |
| Shrinkage rate | |||
| MD | 0.70 | % | ASTM D955 |
| Water absorption rate | |||
| 24hr | 0.37 | % | ASTM D570 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | 2340 | MPa | ASTM D638 |
| tensile strength | |||
| fracture | 69.6 | MPa | ASTM D638 |
| yield | 69.6 | MPa | ASTM D638 |
| Tensile strain | |||
| fracture | 60 | % | ASTM D638 |
| yield | 7.2 | % | ASTM D638 |
| Bending modulus | 2410 | MPa | ASTM D790 |
| bending strength | |||
| yield | 91.0 | MPa | ASTM D790 |
| Compression modulus | 1730 | MPa | ASTM D695 |
| compressive strength | 98.9 | MPa | ASTM D695 |
| shear strength | 62.7 | MPa | ASTM D732 |
| Poisson’s ratio | 0.42 | ASTM E132 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | 690 | J/m | ASTM D256 |
| Impact strength of cantilever beam notch | No Break | ASTM D256 | |
| Tensile impact strength | 399 | kJ/m² | ASTM D1822 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed | 207 | ℃ | ASTM D648 |
| 0.45 MPa, unannealed | 214 | ℃ | ASTM D648 |
| Glass transition temperature | 220 | ℃ | ASTM E1356 |
| Linear coefficient of thermal expansion | |||
| MD | 5.6E-5 | 1/℃ | ASTM D696 |
| Thermal conductivity coefficient | 0.35 | W/m/K | ASTM C177 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volume resistivity | 9.0E+15 | ohms·cm | ASTM D257 |
| Dielectric strength | 14 | kV/mm | ASTM D149 |
| Dielectric constant | ASTM D150 | ||
| 60 Hz | 3.44 | ASTM D150 | |
| 1 kHz | 3.40 | ASTM D150 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| 0.75 mm，ALL colors，UL file E36098 | V-0 | UL 94 | |
| Extreme oxygen index | 38 | % | ASTM D2863 |
| optical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Refractive index | 1.672 | ASTM D542 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 149 | °C | |
| Drying time | 2.5 | hr | |
| Recommended maximum moisture content | 0.050 | % | |
| Barrel rear temperature | 321 | °C | |
| Barrel middle temperature | 349 | °C | |
| Barrel front temperature | 349 | °C | |
| Processing (melt) temperature | 343 to 388 | °C | |
| Mold temperature | 138 to 163 | °C | |
| Back pressure | 0.345 to 0.689 | MPa | |
| Screw compression ratio | 2.2:1.0 | ||
| Notes |
|---|
| 1. For limited exposure (less than 24 hours). |
| 2. NSF STD-51 compliant for NT15 only. |
| 3. NSF STD-61 compliant for BK937, NT15 and GY1037 only. Tested at 82 °C (180 °F) (Commercial Hot). |
| 4. Typical properties: these are not to be construed as specifications. |
| 5. These flammability ratings are not intended to reflect hazards presented by these or any other materials under actual fire conditions. |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |