| About |
|---|
| Product Description | |
|---|---|
| Supplier | Radici |
| Generic | PA66 |
| Material Status | Commercial: Negative |
| Features | V-0,Halogen free,Flame Characteristics,Low to no phosphorus content |
| Availabilitys | Africa & Middle East ,Asia Pacific,Latin America,Europe,North America |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.17 | g/cm³ | ISO 1183 |
| Shrinkage rate | ISO 294-4 | ||
| TD | 1.1 | % | ISO 294-4 |
| MD | 1.1 | % | ISO 294-4 |
| Water absorption rate | |||
| Saturation, 23 ℃, 2.00 mm | 7.7 | % | ISO 62 |
| Equilibrium, 23 ℃, 50% RH, 2.00 mm | 1.8 | % | ISO 62 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | |||
| 1 mm/min | 3500 | MPa | ISO 527-2/1A/1 |
| tensile strength | |||
| Yield, 50 mm/min | 75 | MPa | ISO 527-2/1A/50 |
| Nominal tensile fracture strain | |||
| 50 mm/min | 12 | % | ISO 527-2/1A/50 |
| Bending modulus | |||
| 2 mm/min | 3300 | MPa | ISO 178 |
| bending strength | |||
| 2 mm/min | 110 | MPa | ISO 178 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | |||
| 23℃ | 4.5 | kJ/m² | ISO 179/1eA |
| -30°C | 4 | kJ/m² | ISO 179/1eA |
| Charpy impact strength | |||
| 23℃ | 75 | KJ/m² | ISO 179/1eU |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.80 MPa, unannealed | 70 | ℃ | ISO 75-2/Af |
| 0.45 MPa, unannealed | 200 | ℃ | ISO 75-2/Bf |
| Vicat Softening Temp | |||
| 50℃/h，50N | 220 | ℃ | ISO 306 |
| Melting temperature | 260 | ℃ | ISO 11357 |
| Temperature index | |||
| 50% loss of tensile strength | 151 | ℃ | ISO 2578 |
| 50% loss of tensile strength | 121 | ℃ | ISO 2578 |
| 50% dielectric strength loss | 186 | ℃ | ISO 2578 |
| 50% dielectric strength loss | 134 | ℃ | ISO 2578 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Surface resistivity | |||
| 500V | 1.0E+12 | ohms | IEC 60093 |
| Volume resistivity | |||
| 500V | 1.0E+13 | ohms·cm | IEC 60093 |
| Compared to the leakage tracing index | 600 | V | IEC 60112 |
| Dielectric strength | 31 | kV/mm | IEC 60243-1 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | |||
| 0.4 mm | V-0 | calss | UL 94 |
| 0.8 mm | V-0 | calss | UL 94 |
| Glowing wire flammability index | |||
| 1 mm | 960 | ℃ | IEC 60695-2-12 |
| 2 mm | 960 | ℃ | IEC 60695-2-12 |
| Igniting temperature of the hot wire | |||
| 1 mm | ＞775 | ℃ | IEC 60695-2-13 |
| 2 mm | ＞750 | ℃ | IEC 60695-2-13 |
| Extreme oxygen index | |||
| 23℃ | 35 | % | ISO 4589-2 |
| Process Conditions | |||
|---|---|---|---|
| Injection | Nominal value | Unit | Test method |
| extrusion | Nominal value | Unit | Test method |
| Drying temperature – hot air dryer | 80 | °C | null |
| Drying time – hot air dryer | 2.0 – 4.0 | hr | null |
| Dew Point – Hot Air Dryer | < -20 | °C | null |
| Recommended maximum moisture content | 0.10 | % | null |
| Processing (melt) temperature | 270 – 290 | °C | null |
| Mold temperature | 60 – 80 | °C | null |
| Injection speed | 中速 | null | |
| drying temperature | 80 | °C | null |
| Drying time | 2.0 – 4.0 | hr | null |
| Recommended maximum moisture content | 0.10 | % | null |
| Melt Temperature | 270 – 290 | °C | null |
| Notes |
|---|
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |