| About |
|---|
| Product Description | |
|---|---|
| Supplier | Radici |
| Generic | PA6 |
| Material Status | Commercial: Negative |
| Features | V-0,Halogen free,Flame Characteristics,Low to no phosphorus content |
| Availabilitys | Africa & Middle East ,Asia Pacific,Latin America,Europe,North America |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1420 | kg/m³ | ISO 1183 |
| Molding shrinkage | |||
| Parallel | 0.3 | % | ISO 294-4 |
| Normal | 0.6 | % | ISO 294-4 |
| Water Absorption | 5.2 | % | ISO 62 |
| Moisture Absorption | 1.6 | % | ISO 62 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile Modulus | 11200 | MPa | ISO 527 |
| Tensile Stress | |||
| Broken BRK | 150 | MPa | ISO 527-2/1A |
| Tensile Strain | |||
| Broken BRK | 3 | % | ISO 527 |
| Flexural Modulus | 9900 | MPa | ISO 178 |
| Flexural Strength | 235 | MPa | ISO 178 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Unnotch Impact strength | 65 | kJ/m² | ISO 179/1eU |
| Charpy Notched Impact Strength | 7 | kJ/m² | ISO 179/1eA |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Melting temperature | 220 | ℃ | ISO 11357-3 |
| Hot deformation temperature HDT | |||
| 1.80 MPa | 190 | ℃ | ISO 75-1/-2 |
| Vicat Softening Temperature | 210 | ℃ | ISO 306/B |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame Class Rating | |||
| 0.8 mm | V-0 | calss | UL 94 |
| Glow Wire Flammability Index (GWFI) | |||
| 1 mm | 960 | ℃ | IEC 60695-2-12 |
| 2 mm | 960 | ℃ | IEC 60695-2-12 |
| Glow Wire Ignitability Temperature (GWIT) | |||
| 1 mm | 725 | ℃ | IEC 60695-2-13 |
| 2 mm | 725 | ℃ | IEC 60695-2-13 |
| ELECTRICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Volume Resistance | 1E13 | ohm·m | IEC 60093 |
| Surface Resistivity | 1E12 | ohm | IEC 60093 |
| Compared Tracking Index | 550 | IEC 60112 |
| Process Conditions | |||
|---|---|---|---|
| Extrusion Molded | Nominal value | Unit | Test method |
| Injection Molding | Nominal value | Unit | Test method |
| Drying Temperature | 80 | °C | null |
| Drying Time | 2.0 – 4.0 | hr | null |
| Maximum Moisture Content | 0.10 | % | null |
| Melt Temperature | 250 – 280 | °C | null |
| Drying Temperature | 80 | °C | null |
| Drying Time | 2.0 – 4.0 | hr | null |
| Dew Point | < -20 | °C | null |
| Maximum Moisture Content | 0.10 | % | null |
| Melt Temperature | 250 – 280 | °C | null |
| Mold Temperature | 80 – 100 | °C | null |
| Injection speed | 中速 – 高速 | null | |
| Notes |
|---|
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |