Resiten® 100 - SOLIAO

About
Resiten® 100 is a Phenolic material. It is available in North America. Important attributes of Resiten® 100 are: Flame Rated REACH Compliant RoHS Compliant&&

Product Description
Generic	酚醛树脂
Material Status	Commercial: Active
Features	Good Electrical Properties,HB,V-0
Availabilitys	North America

MECHANICAL	Nominal value	Unit	Test method
tensile strength			ASTM D638
MD，1.57 mm	164	MPa	ASTM D638
TD，1.57 mm	122	MPa	ASTM D638
MD，3.18 mm	176	MPa	ASTM D638
TD，3.18 mm	121	MPa	ASTM D638
bending strength			ASTM D790
1.57 mm	200	MPa	ASTM D790
1.57 mm	177	MPa	ASTM D790
3.18 mm	185	MPa	ASTM D790
3.18 mm	168	MPa	ASTM D790
12.70 mm	186	MPa	ASTM D790
12.70 mm	146	MPa	ASTM D790
compressive strength
1.57 mm	71.7	MPa	ASTM D695
1.57 mm	57.9	MPa	ASTM D695
3.18 mm	136	MPa	ASTM D695
12.7 mm	390	MPa	ASTM D695
12.7 mm	389	MPa	ASTM D695

IMPACT	Nominal value	Unit	Test method
Impact strength of cantilever beam notch			ASTM D256
TD，1.57mm	29	J/m	ASTM D256
TD，3.2mm	26	J/m	ASTM D256
TD，12.7mm	28	J/m	ASTM D256
Flow rate, 1.57mm	35	J/m	ASTM D256
Flow rate, 3.18mm	30	J/m	ASTM D256
Flow rate, 12.7mm	35	J/m	ASTM D256

THERMAL	Nominal value	Unit	Test method
Relative temperature index
Electrical performance, 1.60 mm	130	℃	UL 746
1.60 mm	130	℃	UL 746

Electrical performance	Nominal value	Unit	Test method
Dielectric strength			ASTM D149
1.57 mm	28	kV/mm	ASTM D149
3.18 mm	18	kV/mm	ASTM D149
Dielectric constant			ASTM D150
1.57 mm，60 Hz	8.01		ASTM D150
1.57 mm，1 kHz	6.28		ASTM D150
1.57 mm，1 MHz	5.00		ASTM D150
3.18 mm，60 Hz	9.67		ASTM D150
3.18 mm，1 kHz	7.07		ASTM D150
3.18 mm，1 MHz	5.42		ASTM D150
Dissipation factor			ASTM D150
1.57 mm，1 kHz	0.10		ASTM D150
1.57 mm，60 kHz	0.26		ASTM D150
1.57 mm，1 MHz	0.041		ASTM D150
3.18 mm，1 kHz	0.13		ASTM D150
3.18 mm，60 kHz	0.33		ASTM D150
3.18 mm，1 MHz	0.047		ASTM D150
Arc resistance			ASTM D495
1.57 mm	78.0	sec	ASTM D495
3.18 mm	79.0	sec	ASTM D495
12.7 mm	82.0	sec	ASTM D495
Compared to the resistance to leakage and marking index
1.57 mm	210	V	UL 746
High Arc Burning Index (HAI) (1.57 mm)	> 200		UL 746
High voltage arc marking rate (HVTR) (1.57 mm)	5.00	mm/min	UL 746
Hot wire ignition (HWI) (1.57 mm)	15	sec	UL 746
breakdown voltage			ASTM D149
1.57 mm	78000	V	ASTM D149
3.18 mm	60000	V	ASTM D149
1.27 cm	42000	V	ASTM D149

FLAME CHARACTERISTICS	Nominal value	Test method
Flame retardant level		UL 94
1.60 mm	HB	UL 94
3.20 mm	HB	UL 94
12.70 mm	V-0	UL 94

Notes
1. Typical properties: these are not to be construed as specifications.
2. Flow, Condition A
3. Across Flow, Condition A
4. Flow
5. Across Flow
6. Condition A
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.