| About |
|---|
| RIALOX B 120 GF30 ST F V-0 natural is a semi-crystalline thermoplastic flame-retardant construction material based on polybutylene terephthalate (PBT), reinforced with 30% glass fibers. RIALOX B 120 GF30 ST F V-0 natural will be processed by injection molding. It is used for parts for which a halogen-free PBT with fire protection equipment is required. The product is available in all colours. RIALOX B 120 GF30 ST F V-0 natural is characterized by the following properties: UL 94 V-0 from 0.4 mm Tracking resistance 600 V GWIT 775 °C conform at 3 mm GWFI 960 °C from 0.75 mm Very good dimensional stability Very good elongation behavior WEEE and RoHS conformity&& |
| Product Description | |
|---|---|
| Generic | polybutylene terephthalate |
| Material Status | Commercial: Active |
| Features | Good Dimensional Stability,Halogen free,Flame Characteristics,Hypocrystalline,V-0 |
| Availabilitys | Africa & Middle East ,North America,Latin America,Asia Pacific,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.51 | g/cm³ | ISO 1183 |
| Melt Volume Rate | |||
| 250℃，2.16 kg | 3.50 | cm³/10min | ISO 1133 |
| Shrinkage rate | ISO 294-4 | ||
| TD | 0.20 to 0.60 | % | ISO 294-4 |
| MD | 0.10 to 0.40 | % | ISO 294-4 |
| Water absorption rate | ISO 62 | ||
| Saturation, 23 ℃ | 0.40 | % | ISO 62 |
| Equilibrium, 23 ℃, 50% RH | 0.20 | % | ISO 62 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | 9500 | MPa | ISO 527-1-2 |
| tensile strength | |||
| fracture | 95.0 | MPa | ISO 527-2/5 |
| Tensile strain | |||
| fracture | 3.1 | % | ISO 527-2/5 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | |||
| 23℃ | 8.3 | kJ/m² | ISO 179/1eA |
| Charpy Unnotch Impact strength | |||
| 23℃ | 42 | kJ/m² | ISO 179/1eU |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 0.45 MPa, unannealed | 224 | ℃ | ISO 75-2/B |
| 1.8 MPa, unannealed | 212 | ℃ | ISO 75-2/A |
| Vicat Softening Temp | |||
| B50 | 193 | ℃ | ISO 306 |
| Maximum operating temperature | |||
| Continuous | 150 | ℃ | |
| Short Time | 200 | ℃ |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Surface resistivity | > 1.0E+13 | ohms | IEC 60093 |
| Volume resistivity | > 1.0E+15 | ohms·cm | IEC 60093 |
| Dielectric constant | IEC 60250 | ||
| 100 Hz | 3.90 | IEC 60250 | |
| 1 MHz | 3.50 | IEC 60250 | |
| Compared to the leakage tracing index | 600 | V | IEC 60112 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| 4.00 mm | V-0 | UL 94 | |
| Glowing wire flammability index | |||
| 0.75 mm | 960 | ℃ | IEC 60695-2-12 |
| Igniting temperature of the hot wire | IEC 60695-2-13 | ||
| 0.75 mm | 775 | ℃ | IEC 60695-2-13 |
| 3 mm | 775 | ℃ | IEC 60695-2-13 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 120 | °C | |
| Drying time | 2.0 to 4.0 | hr | |
| Recommended maximum moisture content | 0.030 | % | |
| Hopper temperature | 50 to 70 | °C | |
| Barrel rear temperature | 230 to 250 | °C | |
| Barrel middle temperature | 240 to 260 | °C | |
| Barrel front temperature | 250 to 270 | °C | |
| Nozzle temperature | 250 to 270 | °C | |
| Processing (melt) temperature | 250 to 270 | °C | |
| Mold temperature | 60 to 100 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |