Rilsan® BESHV BLK T

About
Rilsan® BESHV BLK T is an ultra high viscosity Polyamide 11 grade specifically designed to be extruded into large diameter thick wall pipe. This grade has been specifically engineered to achieve an outstanding balance of properties for Oil & Gas piping applications. It offers a cost effective system for non-metallic corrosion free fluid transfer in critical Oil and Gas industry applications. Rilsan® Polyamide 11 is the only thermoplastic material permitted by the US Department of Transportation (DOT) under the Code of Federal Regulations (CFR) Title 49, Part 192, for gas distribution piping to be installed and operated at pressures up to and including 200 psi in a design factor of 0.40 MAIN APPLICATIONS Oil & Gas piping applications.&&

About

Rilsan® BESHV BLK T is an ultra high viscosity Polyamide 11 grade specifically designed to be extruded into large diameter thick wall pipe. This grade has been specifically engineered to achieve an outstanding balance of properties for Oil & Gas piping applications. It offers a cost effective system for non-metallic corrosion free fluid transfer in critical Oil and Gas industry applications. Rilsan® Polyamide 11 is the only thermoplastic material permitted by the US Department of Transportation (DOT) under the Code of Federal Regulations (CFR) Title 49, Part 192, for gas distribution piping to be installed and operated at pressures up to and including 200 psi in a design factor of 0.40 MAIN APPLICATIONS Oil & Gas piping applications.&&

Product Description
Supplier	Arkema
Generic	PA 11
Material Status	Commercial: Active
Features	High Viscosity,Renewable resources
Availabilitys	Africa & Middle East ,North America,Latin America,Asia Pacific,Europe
Process Methods	Extrusion

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	1.03	g/cm³	ISO 1183

MECHANICAL	Nominal value	Unit	Test method
Shore hardness			ISO 868
Shaw’s D	77		ISO 868
Shore D, 15 seconds	72		ISO 868
Tensile modulus	1390	MPa	ISO 527-2
tensile strength
fracture	52.0	MPa	ISO 527-2
yield	42.0	MPa	ISO 527-2
Tensile strain
fracture	> 200	%	ISO 527-2
yield	5.0	%	ISO 527-2
Bending modulus	1180	MPa	ISO 178

IMPACT	Nominal value	Unit	Test method
Charpy Notched Impact Strength			ISO 179
-30℃	11	kJ/m²	ISO 179
23℃	10	kJ/m²	ISO 179
Charpy Unnotch Impact strength			ISO 179
-30℃	No Break		ISO 179
23℃	No Break		ISO 179

THERMAL	Nominal value	Unit	Test method
Melting temperature	189	℃	ISO 11357-3

Supplementary information	Nominal value	Unit	Test method
ASTM Classification	PA0320 B32300		ASTM D4066
Renewable Carbon Conent	> 95	%	ASTM D6866

Process Conditions
injection	Nominal value	Unit	Test method
Drying temperature	176	°C
Drying time	12	hr
Processing (melt) temperature	240 to 290	°C
Mold temperature	20 to 60	°C

Notes
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.