| About |
|---|
| SABIC® LDPE 1922N0 is an additive free LDPE grade produced by SABIC’s CTR® tubular technology. This grade is typically developed for food contact applications that require high product quality, consistency and high level of purity. SABIC will offer for SABIC® LDPE 1922N0 the full food compliance service package. Application. SABIC® LDPE 1922N0 is typically suitable for applications that require a good balance between flow properties and mechanical properties. This product is not intended for and must not be used in any pharmaceutical/medical applications.&& |
| Product Description | |
|---|---|
| Supplier | SABIC |
| Generic | LDPE |
| Material Status | Commercial: Active |
| Features | High purity,Food contact compliance,Low density |
| Availabilitys | Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 0.919 | g/cm³ | ISO 1183 |
| Melt Flow Rate | ISO 1133 | ||
| 190℃，2.16kg | 22 | g/10min | |
| 190℃，5.0kg | 75 | g/10min | |
| Melt Volume Rate | ISO 1133 | ||
| 190℃，2.16 kg | 29.0 | cm³/10min | |
| 190℃，5 kg | 98.0 | cm³/10min | |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | ISO 180/A | ||
| -30 ℃, molded | 5.0 | kJ/m² | |
| 23 ℃, molded | 42 | kJ/m² |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 0.45 MPa, unannealed | 39.0 | ℃ | ISO 75-2/B |
| Vicat Softening Temp | 82.0 to 83.0 | ℃ | ISO 306/A |
| Melting temperature | |||
| DSC | 105 to 107 | ℃ | DIN 53765 |
| Enthalpy Change | 104 | J/g | DIN 53765 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | |||
| Shaw’s D, molded | 40 | ISO 868 | |
| Tensile modulus | |||
| 2 mm, molded into shape | 175 | MPa | ISO 527-2/1BA/50 |
| tensile strength | ISO 527-2/1BA/50 | ||
| Yield, 2 mm, molded | 8.00 | MPa | |
| Fracture, 2 mm, molded | 7.00 | MPa | |
| Tensile strain | |||
| Fracture, 2 mm, molded | 400 | % | ISO 527-2/1BA/50 |
| Tensile creep modulus | ISO 899-1 | ||
| 1 hr | 80.0 | MPa | |
| 1000 hr | 45.0 | MPa |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 4mm |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |