SABIC® LDPE PCG06

About
SABIC® LDPE grades for healthcare applications are produced under controlled conditions resulting in high product quality, consistency and a high level of purity. SABIC® LDPE PCG06 is an additive-free grade with high purity and very low migration levels. It is typically used for semi-rigid IV containers for Large Volume Parenterals (LVP) obtained by Blow Fill Seal (BFS) process. Compliance to Regulations SABIC® LDPE PCG06 complies with the relevant monographs of the European Pharmacopoeia (EP) and the United States Pharmacopoeia (USPVI).&&

About

SABIC® LDPE grades for healthcare applications are produced under controlled conditions resulting in high product quality, consistency and a high level of purity. SABIC® LDPE PCG06 is an additive-free grade with high purity and very low migration levels. It is typically used for semi-rigid IV containers for Large Volume Parenterals (LVP) obtained by Blow Fill Seal (BFS) process. Compliance to Regulations SABIC® LDPE PCG06 complies with the relevant monographs of the European Pharmacopoeia (EP) and the United States Pharmacopoeia (USPVI).&&

Product Description
Supplier	SABIC
Generic	LDPE
Material Status	Commercial: Active
Features	High purity,Low density,Low to no mobility
Availabilitys	Europe

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	0.928	g/cm³	ISO 1183/A
Melt Flow Rate
190℃，2.16kg	0.55	g/10min	ISO 1133

MECHANICAL	Nominal value	Unit	Test method
friction coefficient	1.0		ASTM D1894

film	Nominal value	Unit	Test method
Tensile modulus			ISO 527-3
MD	290	MPa	ISO 527-3
TD	340	MPa	ISO 527-3
tensile strength			ISO 527-3
MD, yield	13.0	MPa	ISO 527-3
TD, yield	14.0	MPa	ISO 527-3
MD, fracture	21.0	MPa	ISO 527-3
TD, fracture	22.0	MPa	ISO 527-3
Tensile strain			ISO 527-3
MD, fracture	> 200	%	ISO 527-3
TD, fracture	> 500	%	ISO 527-3

IMPACT	Nominal value	Unit	Test method
Izod notched impact strength	250	J/cm	ASTM D4272

THERMAL	Nominal value	Unit	Test method
Vicat Softening Temp	106	℃	ISO 306/A
Melting temperature
DSC	115	℃	DIN 53765

optical performance	Nominal value	Unit	Test method
gloss
45°	70		ASTM D2457
Haze	6.0	%	ASTM D1003A

Supplementary information	Nominal value	Unit	Test method
Blocking force	10	g	Internal Method
Re（blocking）	30	g	Internal Method
tear strength			ISO 6383-2
MD	45.0	kN/m	ISO 6383-2
TD	35.0	kN/m	ISO 6383-2

Notes
1. Typical properties: these are not to be construed as specifications.
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

1. Typical properties: these are not to be construed as specifications.

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.