| About |
|---|
| Product Description 218 series resins are Linear Low Density Polyethylene grades suitable for general purpose packaging. They are easy to process giving good tensile properties, impact strength and optical properties. 218 Series includes following grades: 218N: No Slip & No Antiblock 218W: 1500 ppm Slip & 3500 ppm Antiblock Typical Applications Lamination film, thin liners, shopping bags, carrier bags, garbage bags, coextruded films, consumer packaging etc.&& |
| Product Description | |
|---|---|
| Supplier | SABIC |
| Generic | Linear low density polyethylene |
| Material Status | Commercial: Active |
| Features | Good flexibility,High impact resistance,Smoothness,Good dissection,Optical performance,High anti-blocking,Good Tensile Strength,Copolymer |
| Availabilitys | North America,Latin America |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 0.918 | g/cm³ | ASTM D1505 |
| Melt Flow Rate | |||
| 190℃，2.16kg | 2.0 | g/10min | ASTM D1238 |
| film | Nominal value | Unit | Test method |
|---|---|---|---|
| film thickness | |||
| test | 30 | µm | |
| Secant modulus | ASTM D882 | ||
| MD：30 µm | 220 | MPa | ASTM D882 |
| TD：30 µm | 260 | MPa | ASTM D882 |
| tensile strength | ASTM D882 | ||
| MD, yield, 30 µ m | 12.0 | MPa | ASTM D882 |
| TD, yield, 30 µ m | 10.0 | MPa | ASTM D882 |
| MD, fracture, 30 µ m | 35.0 | MPa | ASTM D882 |
| TD, fracture, 30 µ m | 29.0 | MPa | ASTM D882 |
| Tensile strain | ASTM D882 | ||
| MD, fracture, 30 µ m | 700 | % | ASTM D882 |
| TD, fracture, 30 µ m | 750 | % | ASTM D882 |
| Drop hammer impact | |||
| 30 µm | 85 | g | ASTM D1709 |
| Elmandorf tear strength | ASTM D1922 | ||
| MD：30 µm | 130 | g | ASTM D1922 |
| TD：30 µm | 320 | g | ASTM D1922 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Vicat Softening Temp | 98.0 | ℃ | ASTM D1525 |
| optical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| gloss | |||
| 45°，30 µm | 80 | ASTM D2457 | |
| Haze | |||
| 30 µm | 13 | % | ASTM D1003 |
| Supplementary information | Nominal value | Unit | Test method |
|---|---|---|---|
| Puncture resistance | |||
| 30.0 µm | 630 | J/cm | Internal Method |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |