SABIC® LLDPE MG500026

About
SABIC® LLDPE MG500026 SABIC® LLDPE MG50026 is a high flow linear density copolymer grade with a narrow molecular weight distribution. SABIC® LLDPE MG50026 resin is in powder form. Application SABIC® LLDPE MG500026 typically used for injection moulding masterbatches where a high filler acceptance is required, combined with a good flow. Since the resin is supplied in free flowing powder form it can be used for masterbatch production where PE powders are used. This product is not intended for and must not be used in any pharmaceutical/medical applications.&&SABIC® LLDPE MG500026 SABIC® LLDPE MG50026 is a high flow linear density copolymer grade with a narrow molecular weight distribution. SABIC® LLDPE MG50026 resin is in powder form. SABIC® LLDPE MG500026 resin is recommended for injection moulding masterbatch where a high filler acceptance is required, combined with a good flow. Since the resin is supplied in powder form it is extremely suited for masterbatch production where PE powders are used. The product mentioned herein is in particular not tested and therefore not validated for use in pharmaceutical/medical applications.&&

About

SABIC® LLDPE MG500026 SABIC® LLDPE MG50026 is a high flow linear density copolymer grade with a narrow molecular weight distribution. SABIC® LLDPE MG50026 resin is in powder form. Application SABIC® LLDPE MG500026 typically used for injection moulding masterbatches where a high filler acceptance is required, combined with a good flow. Since the resin is supplied in free flowing powder form it can be used for masterbatch production where PE powders are used. This product is not intended for and must not be used in any pharmaceutical/medical applications.&&SABIC® LLDPE MG500026 SABIC® LLDPE MG50026 is a high flow linear density copolymer grade with a narrow molecular weight distribution. SABIC® LLDPE MG50026 resin is in powder form. SABIC® LLDPE MG500026 resin is recommended for injection moulding masterbatch where a high filler acceptance is required, combined with a good flow. Since the resin is supplied in powder form it is extremely suited for masterbatch production where PE powders are used. The product mentioned herein is in particular not tested and therefore not validated for use in pharmaceutical/medical applications.&&

Product Description
Supplier	SABIC
Generic	Linear low density polyethylene
Material Status	Commercial: Active
Features	High liquidity,Weight distribution,Low density,Copolymer
Availabilitys	North America,Latin America,Europe
Process Methods	Injection Molding

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	0.926	g/cm³	ASTM D1505
Melt Flow Rate
190℃，2.16kg	50	g/10min	ASTM D1238
ESCR(Environmental Stress Cracking Resistance)
Compression Molding	2.00	hr	ASTM D1693

IMPACT	Nominal value	Unit	Test method
Impact strength of cantilever beam notch
23 ℃, molded	450	J/m	ASTM D256

THERMAL	Nominal value	Unit	Test method
Embrittlement temperature	< -75.0	℃	ASTM D746
Vicat Softening Temp	88.0	℃	ASTM D1525 1

MECHANICAL	Nominal value	Unit	Test method
Shore hardness
Shaw’s D, molded	55		ASTM D2240
Tensile modulus
1% cut, molded	354	MPa	ASTM D638
tensile strength			ASTM D638
Yield, molding	13.0	MPa
Fracture, molded	12.4	MPa
Tensile strain
Fracture, molded	120	%	ASTM D638

Process Conditions
injection	Nominal value	Unit	Test method
Processing (melt) temperature	180 to 230	°C

Notes
1. Typical properties: these are not to be construed as specifications.
2. Loading 1 (10 N)
3. Rate A (50°C/h), Loading 1 (10 N)
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.