SABIC® LLDPE R50035EE

About
SABIC® LLDPE R50035EE is a LLDPE copolymer that typically provides good stress crack resistance, rigidity, toughness, gloss and very low warpage. The resin contains UV stabilizer. It is recommended that SABIC® LLDPE R50035EE is grinded before use in rotational moulding applications. Typical Applications. SABIC® LLDPE R50035EE is typically used for rotational moulding of large industrial and agricultural tanks, trash containers and chemical shipping drums. Because of its good mechanical properties and low warpage, it is typically used for injection moulding of screw closures, caps and housewares. SABIC® LLDPE R50035EE is UV stabilised; which provides good protection for the final product. This product is not intended for and must not be used in any pharmaceutical/medical applications.&&

About

SABIC® LLDPE R50035EE is a LLDPE copolymer that typically provides good stress crack resistance, rigidity, toughness, gloss and very low warpage. The resin contains UV stabilizer. It is recommended that SABIC® LLDPE R50035EE is grinded before use in rotational moulding applications. Typical Applications. SABIC® LLDPE R50035EE is typically used for rotational moulding of large industrial and agricultural tanks, trash containers and chemical shipping drums. Because of its good mechanical properties and low warpage, it is typically used for injection moulding of screw closures, caps and housewares. SABIC® LLDPE R50035EE is UV stabilised; which provides good protection for the final product. This product is not intended for and must not be used in any pharmaceutical/medical applications.&&

Product Description
Supplier	SABIC
Generic	Linear low density polyethylene
Material Status	Commercial: Active
Features	High Heat Resistance
Availabilitys	Africa & Middle East
Process Methods	Injection Molding

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	0.933	g/cm³	ASTM D1505
Melt Flow Rate
190℃，2.16kg	5.0	g/10min	ASTM D1238
ESCR(Environmental Stress Cracking Resistance)
100% non-ionic detergent, molded, F50	> 150	hr	ASTM D1693B

THERMAL	Nominal value	Unit	Test method
Embrittlement temperature	< -75.0	℃	ASTM D746
Vicat Softening Temp	114	℃	ASTM D1525

MECHANICAL	Nominal value	Unit	Test method
Shore hardness
Shaw’s D, molded	66		ASTM D2240
tensile strength			ASTM D638
Yield, molding	16.0	MPa	ASTM D638
Fracture, molded	17.0	MPa	ASTM D638
Tensile strain
Fracture, molded	590	%	ASTM D638
Bending modulus
1% cut, molded	420	MPa	ASTM D790
bending strength
Compression Molding	13.0	MPa	ASTM D790

Process Conditions
injection	Nominal value	Unit	Test method
Processing (melt) temperature	210 to 240	°C

Notes
1. Typical properties: these are not to be construed as specifications.
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

1. Typical properties: these are not to be construed as specifications.

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.