SABIC® PP 500P

About
SABIC® PP 500P SABIC® PP 500P is a medium flow, multipurpose grade for extrusion and injection moulding applications. If applied for extrusion this grade shows an excellent stretch ability and is therefore suitable for tapes and strapping, high tenacity yarns and carpet backing. For thermoforming it shows a unique balance between transparency, impact resistance and thickness uniformity. SABIC PP 500P is suitable for production of injection moulded articles e.g. caps and closures and house ware products, where this grade shows a high stiffness, combined with a fair impact resistance and very good surface hardness. SABIC® PP 500P is a medium flow grade typically used in extrusion applications like sheet and thermoforming. SABIC® PP 500P is typically used in dairy, flower pots, yellow fats and disposables plates and cups. However, customers use this grade also in combination with fillers like Talc and CaCO3. The product mentioned herein is in particular not tested and therefore not validated for use in pharmaceutical/medical applications.&&SABIC® PP 500P PP Homopolymer for Raffia applications PP 500P is specially developed for producing stretched tapes with following features. Consistent processability Easy orientation Low water carry over Good mechanical properties Typical Applications PP 500P can be used for producing woven bags, flexible intermediate bulk containers, ropes & twines, carpet backing, geotextiles and concrete reinforcements.&&

About

SABIC® PP 500P SABIC® PP 500P is a medium flow, multipurpose grade for extrusion and injection moulding applications. If applied for extrusion this grade shows an excellent stretch ability and is therefore suitable for tapes and strapping, high tenacity yarns and carpet backing. For thermoforming it shows a unique balance between transparency, impact resistance and thickness uniformity. SABIC PP 500P is suitable for production of injection moulded articles e.g. caps and closures and house ware products, where this grade shows a high stiffness, combined with a fair impact resistance and very good surface hardness. SABIC® PP 500P is a medium flow grade typically used in extrusion applications like sheet and thermoforming. SABIC® PP 500P is typically used in dairy, flower pots, yellow fats and disposables plates and cups. However, customers use this grade also in combination with fillers like Talc and CaCO3. The product mentioned herein is in particular not tested and therefore not validated for use in pharmaceutical/medical applications.&&SABIC® PP 500P PP Homopolymer for Raffia applications PP 500P is specially developed for producing stretched tapes with following features. Consistent processability Easy orientation Low water carry over Good mechanical properties Typical Applications PP 500P can be used for producing woven bags, flexible intermediate bulk containers, ropes & twines, carpet backing, geotextiles and concrete reinforcements.&&

Product Description
Supplier	SABIC
Generic	PP homopolymerization
Material Status	Commercial: Active
Features	Good Rigidity,Excellent Processability,High impact resistance,Wide molecular weight distribution,Food contact compliance,Good Tensile Strength,Moderate liquidity,Low water portability,Homopolymer
Availabilitys	North America,Latin America,Europe
Process Methods	Thermo forming

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	0.907	g/cm³	ASTM D792
Melt Flow Rate
230℃，2.16kg	3.0	g/10min	ASTM D1238

IMPACT	Nominal value	Unit	Test method
Impact strength of cantilever beam notch
23℃	25	J/m	ASTM D256

MECHANICAL	Nominal value	Unit	Test method
Rockwell hardness	102	M 级	ASTM D785
tensile strength
23℃	35	MPa	ASTM D638
Tensile strain
Fracture, 23 ℃	10	%	ASTM D638
Bending modulus
23℃	1505	MPa	ASTM D790

Process Conditions
injection	Nominal value	Unit	Test method
Injection temperature
Rear barrel temperature	235-250	°C
Central temperature of the barrel	235-250	°C
Barrel front temperature	235-250	°C
Die temperature	235-250	°C

Notes
1. Typical properties: these are not to be construed as specifications.
2. 23°C
3. 0.039 in/min
4. 2.0 in/min
5. testbar 80104mm
6. Rate B (120°C/h)
7. Rate B (120°C/h), Loading 1 (10 N)
8. Rate B (120°C/h), Loading 2 (50 N)
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.