| About |
|---|
| A hard, black, UV resistant thermoplastic vulcanizate (TPV) in the thermoplastic elastomer (TPE) family. This material combines good physical properties and chemical resistance for use in difficult injection molding applications. This grade of Santoprene TPV is shear-dependent and can be processed on conventional thermoplastics equipment for injection molding. It is polyolefin based and recyclable within the manufacturing stream.&& |
| Product Description | |
|---|---|
| Supplier | Celanese |
| Material Status | Commercial: Active |
| Features | Weather resistance is good,Fatigue resistance,High liquidity,Excellent Processability,Good Dimensional Stability,Solvent resistance,Renewable resources,Good surface appearance,HB,Ozone resistance |
| Availabilitys | North America,Asia Pacific,Latin America,Africa & Middle East ,Europe |
| Process Methods | Multiple injection molding,Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | |||
| — | 0.908 | g/cm³ | ASTM D792 |
| — | 0.910 | g/cm³ | ISO 1183 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | |||
| Shore A, 15 seconds, 23 ℃ | 91 | ISO 868 |
| elastic body | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | |||
| TD, fracture, 23 ℃ | 7.30 | MPa | ASTM D412 , ISO 37 |
| TD, 100% strain, 23 ℃ | 4.80 | MPa | ASTM D412 , ISO 37 |
| Tensile strain | |||
| TD, fracture, 23 ℃ | 390 | % | ASTM D412，ISO 37 |
| tear strength | |||
| TD，23℃ | 31.0 | kN/m | ASTM D624 |
| TD，23℃ | 31 | kN/m | ISO 34-1 |
| Compression deformation | |||
| 70℃，22 hr | 53 | % | ASTM D395B |
| 125℃，70 hr | 62 | % | ASTM D395B |
| 70℃，22 hr | 53 | % | ISO 815 |
| 125℃，70 hr | 62 | % | ISO 815 |
| Aging performance | Nominal value | Unit | Test method |
|---|---|---|---|
| The rate of change in tensile strength in air | |||
| 150℃，168 hr | 3.0 | % | ASTM D573 , ISO 188 |
| The rate of change in ultimate elongation in air | |||
| 150℃，168 hr | -24 | % | ASTM D573 , ISO 188 |
| The rate of change in hardness of a hardness tester in the air | |||
| Shaw A, 150 ℃, 168 hr | 1.0 | ASTM D573 , ISO 188 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Embrittlement temperature | -54.0 | ℃ | ASTM D746，ISO 812 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| 1.10 mm | HB | UL 94 |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Die C |
| 3. Method Bb, Angle (Nicked) |
| 4. Type 1 |
| 5. Type A |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |