| About |
|---|
| A soft, colorable, specialty thermoplastic vulcanizate (TPV) in the thermoplastic elastomer (TPE) family. It is designed for use in medical and healthcare applications. This grade of Santoprene TPV is shear-dependent and can be processed on conventional thermoplastics equipment for injection molding or extrusion. It is polyolefin based and recyclable within the manufacturing stream.&& |
| Product Description | |
|---|---|
| Supplier | Celanese |
| Material Status | Commercial: Active |
| Features | Low extract,Ozone resistance,Solvent resistance,Ethylene oxide disinfection,Steam sterilized,Renewable resources,High pressure disinfection,Radiation disinfection,High pressure heat resistance,Good Dimensional Stability,Biocompatible |
| Availabilitys | Africa & Middle East ,Asia Pacific,North America,Latin America,Europe |
| Process Methods | Multiple injection molding,Extrusion,Profile extrusion,Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | |||
| — | 0.958 | g/cm³ | ASTM D792 |
| — | 0.960 | g/cm³ | ISO 1183 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | |||
| Shore A, 15 seconds, 23 ℃ | 60 | ISO 868 |
| elastic body | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile permanent deformation | |||
| 23℃ | 5 | % | ASTM D412 |
| tensile strength | |||
| TD, fracture, 23 ℃ | 4.90 | MPa | ASTM D412 |
| TD, 100% strain, 23 ℃ | 2.00 | MPa | ASTM D412 |
| Tensile strain | |||
| TD, fracture, 23 ℃ | 410 | % | ASTM D412 |
| tear strength | |||
| TD，23℃ | 16.0 | kN/m | ASTM D624 |
| TD，100℃ | 6.00 | kN/m | ASTM D624 |
| TD，23℃ | 16 | kN/m | ISO 34-1 |
| TD，100℃ | 6.0 | kN/m | ISO 34-1 |
| Compression deformation | |||
| 23℃，168 hr | 20 | % | ASTM D395B |
| 100℃，168 hr | 48 | % | ASTM D395B |
| 23℃，168 hr | 20 | % | ISO 815 |
| 100℃，168 hr | 48 | % | ISO 815 |
| Aging performance | Nominal value | Unit | Test method |
|---|---|---|---|
| The rate of change in tensile strength in air | |||
| 100℃，168 hr | 11 | % | ASTM D573 |
| The rate of change in ultimate elongation in air | |||
| 100℃，168 hr | 9.0 | % | ASTM D573 |
| Supplementary information | Nominal value | Unit | Test method |
|---|---|---|---|
| Legal Statement | Nominal value | Unit | Test method |
|---|---|---|---|
| Process Conditions | |||
|---|---|---|---|
| Injection instructions | Nominal value | Unit | Test method |
| Squeeze description | Nominal value | Unit | Test method |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Die C |
| 3. Method Bb, Angle (Nicked) |
| 4. Type 1 |
| 5. Type A |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |