| About |
|---|
| Shinite® PBT D201G30 is a Polybutylene Terephthalate (PBT) material filled with 30% glass fiber. It is available in North America. Important attributes of Shinite® PBT D201G30 are: Flame Rated Chemical Resistant Good Dimensional Stability&& |
| Product Description | |
|---|---|
| Supplier | Shinkong |
| Generic | polybutylene terephthalate |
| Material Status | Commercial: Active |
| Features | Good Dimensional Stability,Good Electrical Properties,Solvent resistance,HB |
| Availabilitys | North America |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.52 | g/cm³ | ASTM D792 |
| Shrinkage rate | |||
| MD | 0.30 to 1.4 | % | ASTM D955 |
| Water absorption rate | |||
| 23℃，24hr | 0.070 | % | ASTM D570 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | |||
| 3.2mm | 91 | J/m | ASTM D256 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed | 208 | ℃ | ASTM D648 |
| Melting temperature | 224 | ℃ | DSC |
| Linear coefficient of thermal expansion | |||
| MD | 3.1E-5 | 1/℃ | ASTM D696 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volume resistivity | 1.0E+16 | ohms·cm | ASTM D257 |
| Dielectric strength | 29 | kV/mm | ASTM D149 |
| Dielectric constant | 2.20 | ASTM D150 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | HB | UL 94 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | 11900 | MPa | ASTM D638 |
| tensile strength | 125 | MPa | ASTM D638 |
| Tensile strain | |||
| fracture | 2.2 | % | ASTM D638 |
| Bending modulus | 8480 | MPa | ASTM D790 |
| bending strength | 189 | MPa | ASTM D790 |
| compressive strength | 157 | MPa | ASTM D695 |
| Rockwell hardness | |||
| R-level | 118 | ASTM D785 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 121 | °C | |
| Drying time | 2.0 to 4.0 | hr | |
| Recommended maximum moisture content | 0.020 | % | |
| Proposed maximum recycled material ratio | 25 | % | |
| Barrel rear temperature | 232 to 260 | °C | |
| Barrel middle temperature | 232 to 260 | °C | |
| Barrel front temperature | 232 to 260 | °C | |
| Processing (melt) temperature | 241 to 260 | °C | |
| Mold temperature | 60 to 121 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |