Silopren® LSR 4020

About
Silopren LSR 4020 TP 3364 is a two-component liquid silicone rubber for injection moulding processes. Silopren LSR 4020 TP 3364 can be used to produce medical technical articles with high transparency and excellent rubber elastic properties. Key Features and Benefits Vulcanizates consisting of Silopren LSR 4020 TP 3364 are distinguished by the following properties: excellent biocompatibility high stability to ozone and ultraviolet light neutral odour and taste sterilisable with ethylene oxide, steam and gamma radiation good transparency high thermal stability high recovery after puncture easy pigmentable with the LSR Colour Pastes. Potential Applications Because of the outstanding properties Silopren LSR 4020 TP 3364 is particularly suitable for the following elastomeric articles: sealing elements, catheters, vibration dampers, tube connectors, parts for medical technical equipment, mats&&

About

Silopren LSR 4020 TP 3364 is a two-component liquid silicone rubber for injection moulding processes. Silopren LSR 4020 TP 3364 can be used to produce medical technical articles with high transparency and excellent rubber elastic properties. Key Features and Benefits Vulcanizates consisting of Silopren LSR 4020 TP 3364 are distinguished by the following properties: excellent biocompatibility high stability to ozone and ultraviolet light neutral odour and taste sterilisable with ethylene oxide, steam and gamma radiation good transparency high thermal stability high recovery after puncture easy pigmentable with the LSR Colour Pastes. Potential Applications Because of the outstanding properties Silopren LSR 4020 TP 3364 is particularly suitable for the following elastomeric articles: sealing elements, catheters, vibration dampers, tube connectors, parts for medical technical equipment, mats&&

Product Description
Supplier	Momentive
Generic	硅橡胶,LSR
Material Status	Commercial: Active
Features	Weather resistance is good,Good Clarity,Steam sterilized,noise reduction,Biocompatible,Low odor,Radiation disinfection,Ozone resistance,Heat Stabilized,Ethylene oxide disinfection,Good coloring
Availabilitys	Africa & Middle East ,North America,Latin America,Asia Pacific,Europe
Process Methods	Injection Molding

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	1.08	g/cm³	DIN 53479

MECHANICAL	Nominal value	Unit	Test method
Shore hardness
Shaw’s A	22		DIN 53505

elastic body	Nominal value	Unit	Test method
tensile strength	6.50	MPa	DIN 53504
Tensile strain
fracture	1000	%	DIN 53504
tear strength	15.0	kN/m	ASTM D624
Compression deformation
175℃，22 hr	20	%	DIN 53517

THERMAL	Nominal value	Unit
Thermosetting components
Component A	按重量计算的混合比: 1.0
Component B	按重量计算的混合比: 1.0
Post curing time
200℃	4.0	hr

Supplementary information	Nominal value	Unit	Test method
Vulcanization（175℃）	10.0	min

Uncured Properties	Nominal value	Unit	Test method
colour
—	Translucent
—	Translucent
viscosity			DIN 53018
20℃	200	Pa·s	DIN 53018
20℃	200	Pa·s	DIN 53018
storage stability
20 ℃	4300	min

Notes
1. Typical properties: these are not to be construed as specifications.
2. Die B
3. Part B
4. Part A
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.