| About |
|---|
| Skyrol® SH62 is an optically very clear and glossy polyester film. SH62 is pretreated on one side with an adhesion promoting coating and the other side with an antistatic coating. SH62 is used in a wide variety of imaging and graphic arts applications.&& |
| Product Description | |
|---|---|
| Supplier | SKC |
| Generic | PET |
| Material Status | Commercial: Active |
| Features | Good surface appearance,Optical performance,Good bond,Antistatic property |
| Availabilitys | North America,Asia Pacific,Europe |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.40 | g/cm³ | ASTM D1505 |
| Shrinkage rate | Internal Method | ||
| MD：150℃，0.05 mm，30 min | 1.5 | % | Internal Method |
| MD：150℃，0.161 mm，30 min | 1.2 | % | Internal Method |
| TD：150℃，0.05 mm，30 min | 0.80 | % | Internal Method |
| TD：150℃，0.161 mm，30 min | 0.30 | % | Internal Method |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| friction coefficient | ASTM D1894 | ||
| With oneself – dynamic | 0.30 | ASTM D1894 | |
| With oneself – dynamic | 0.30 | ASTM D1894 | |
| With oneself – static | 0.40 | ASTM D1894 | |
| With oneself – static | 0.30 | ASTM D1894 |
| film | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | ASTM D882 | ||
| MD, yield, 50 µ m | 228 | MPa | ASTM D882 |
| MD, yield, 160 µ m | 186 | MPa | ASTM D882 |
| TD, yield, 50 µ m | 255 | MPa | ASTM D882 |
| TD, yield, 160 µ m | 200 | MPa | ASTM D882 |
| Tensile strain | ASTM D882 | ||
| MD, fracture, 50 µ m | 140 | % | ASTM D882 |
| MD, fracture, 160 µ m | 210 | % | ASTM D882 |
| TD, fracture, 50 µ m | 110 | % | ASTM D882 |
| TD, fracture, 160 µ m | 120 | % | ASTM D882 |
| optical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| gloss | ASTM D523 | ||
| 50 µm | 189 | ASTM D523 | |
| 161 µm | 186 | ASTM D523 | |
| Transmittance | ASTM D1003 | ||
| 50.0 µm | 90.0 | % | ASTM D1003 |
| 161 µm | 89.0 | % | ASTM D1003 |
| Haze | ASTM D1003 | ||
| 50 µm | 0.90 | % | ASTM D1003 |
| 161 µm | 1.9 | % | ASTM D1003 |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 50 µm |
| 3. 161 µm |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |