SLOVALEN® PC 88 FRD 1

About
Modified copolymer PP with the possibility of changing the ITT-index within the interval 5 – 20 g/10 min. Stabilized against the UV-radiation and atmospheric conditions by the UV stabilizer on the HALS basis. Retarded with the halogen flame retardant. Application – stadium seats with guaranteed life-cycle of the mechanical and surface properties, electrical industry – terminals, coil forms, covers of electrotools, guides. Fulfills 960°C glow wire and flammability in accordance with UL 94 V2. Concerning flammability, it complies with the building norm DIN 4102- B2. Delivered in the full RAL colour scale.&&

About

Modified copolymer PP with the possibility of changing the ITT-index within the interval 5 – 20 g/10 min. Stabilized against the UV-radiation and atmospheric conditions by the UV stabilizer on the HALS basis. Retarded with the halogen flame retardant. Application – stadium seats with guaranteed life-cycle of the mechanical and surface properties, electrical industry – terminals, coil forms, covers of electrotools, guides. Fulfills 960°C glow wire and flammability in accordance with UL 94 V2. Concerning flammability, it complies with the building norm DIN 4102- B2. Delivered in the full RAL colour scale.&&

Product Description
Generic	PP not specified
Material Status	Commercial: Active
Features	Weather resistance is good,Flame Characteristics,Copolymer,Halogenated,V-2
Availabilitys	Europe
Process Methods	Injection Molding

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	0.930	g/cm³	ISO 1183
Melt Flow Rate
230℃，2.16kg	12	g/10min	ISO 1133
Shrinkage rate			STM 64 0808
TD	2.4	%	STM 64 0808
MD	2.4	%	STM 64 0808

MECHANICAL	Nominal value	Unit	Test method
Tensile modulus	1200	MPa	ISO 527-2
tensile strength
yield	28.0	MPa	ISO 527-2
Tensile strain
yield	20	%	ISO 527-2
Bending modulus	1000	MPa	ISO 178
bending strength	35.0	MPa	ISO 178

IMPACT	Nominal value	Unit	Test method
Charpy Notched Impact Strength			ISO 179
-20℃	4.0	kJ/m²	ISO 179
23℃	9.0	kJ/m²	ISO 179
Charpy Unnotch Impact strength			ISO 179
-20℃	110	kJ/m²	ISO 179
23℃	无断裂		ISO 179

THERMAL	Nominal value	Unit	Test method
Hot deformation temperature
0.45 MPa, unannealed	75.0	℃	ISO 75-2/B
Vicat Softening Temp	110	℃	ISO 306/B
Melting temperature
DSC	150	℃	ISO 3146

Electrical performance	Nominal value	Unit	Test method
Surface resistivity	1.0E+16	ohms	IEC 60093
Volume resistivity	1.0E+16	ohms·cm	IEC 60093
Dielectric strength	24	kV/mm	IEC 60243-1
Compared to the leakage tracing index
Solution A	450	V	IEC 60112

FLAME CHARACTERISTICS	Nominal value	Unit	Test method
Flame retardant level	V-2		UL 94
Igniting temperature of the hot wire	960	℃	IEC 60695-2-13

Process Conditions
injection	Nominal value	Unit	Test method
Processing (melt) temperature	200 to 250	°C
Mold temperature	30 to 50	°C
Injection pressure	50.0 to 80.0	MPa

Notes
1. Typical properties: these are not to be construed as specifications.
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

1. Typical properties: these are not to be construed as specifications.

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.