| About |
|---|
| Solaris® is a low viscosity, clear and colorless liquid platinum cure silicone rubber compound designed for use in protecting of electronic components and other assemblies. It will protect components against shock, vibration, moisture, ozone, dust, chemicals and other environmental hazards. The optical clarity of Solaris® makes it suitable for potting solar cells for maximum light transmission or electronic assemblies where component identification is necessary. For best results, use with Solaris® Bonding Primer®. Ultra-transparent Solaris® provides excellent UV resistance yet allows maximum transmission of light. Solaris® features a low viscosity which allows easy flow in and around complex shapes, providing excellent electrical insulation and shock resistance. Solaris® will cure in deep sections or enclosed assemblies without exotherm. Solaris® encapsulant contains no solvents and has no VOC’s. The hydrolytic stability of Solaris® makes it suitable in high humidity environments and at elevated temperatures.&& |
| Product Description | |
|---|---|
| Generic | 硅酮 |
| Material Status | Commercial: Active |
| Features | Weather resistance is good,Good Clarity,Hydrolysis stability,Low Viscosity,noise reduction,Low odor,Moisture resistance,Heat Resistance, Good |
| Availabilitys | Africa & Middle East ,North America,Latin America,Asia Pacific,Europe |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 0.988 | g/cm³ | ASTM D1475 |
| Specific volume | 1.02 | cm³/g | ASTM D1475 |
| Shrinkage rate | |||
| MD | < 0.10 | % | ASTM D2566 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | |||
| Shaw’s A | 15 | ASTM D2240 |
| elastic body | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | |||
| fracture | 1.24 | MPa | ASTM D412 |
| 100% strain | 0.172 | MPa | ASTM D412 |
| Tensile strain | |||
| fracture | 290 | % | ASTM D412 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volume resistivity | 3.2E+15 | ohms·cm | ASTM D257 |
| Dielectric strength | > 14 | kV/mm | ASTM D149 |
| Dielectric constant | |||
| 100 Hz | 2.78 | ASTM D150 | |
| Dissipation factor | |||
| 100 Hz | 0.0 | ASTM D150 |
| optical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Refractive index | 1.410 | ASTM D1218 |
| Supplementary information | Nominal value | Unit | Test method |
|---|---|---|---|
| Mixing ratio | 1A:1B by volume or weight | ||
| working temperature | -101 to 204 | ℃ |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Thermal conductivity coefficient | 0.026 | W/m/K | ASTM D1461 |
| storage stability | |||
| 23℃ | 240 | min | ASTM D2471 |
| Thermosetting mixed viscosity | 1200 | cP | ASTM D2393 |
| stripping time | 1400 | min |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |