| About |
|---|
| Solarkote® P610 is a Polymethyl Methacrylate Acrylic product. It is available in Europe or North America.&& |
| Product Description | |
|---|---|
| Supplier | Arkema |
| Generic | PMMA |
| Material Status | Commercial: Active |
| Availabilitys | North America,Europe |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.14 | g/cm³ | ASTM D792 |
| Melt Flow Rate | |||
| 230℃，3.80kg | 0.80 | g/10min | ASTM D1238 |
| Water absorption rate | |||
| 24hr | 0.40 | % | ASTM D570 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | |||
| 23℃ | 96 | J/m | ASTM D256 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, annealed | 51.7 | ℃ | ASTM D648 |
| Vicat Softening Temp | |||
| — | 68.9 | ℃ | ASTM D1525 2 |
| — | 58.3 | ℃ | ASTM D1525 3 |
| Linear coefficient of thermal expansion | |||
| MD | ASTM E831 | ||
| -18℃ | 1.2E-4 | cm/cm/℃ | ASTM E831 |
| -7℃ | 1.2E-4 | cm/cm/℃ | ASTM E831 |
| 24℃ | 1.4E-4 | cm/cm/℃ | ASTM E831 |
| 38℃ | 1.5E-4 | cm/cm/℃ | ASTM E831 |
| Thermal conductivity coefficient | 0.22 | W/m/K | ASTM C177 |
| optical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Refractive index | 1.490 | ASTM D542 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Rockwell hardness | |||
| R-level | 69 | ASTM D785 | |
| Tensile modulus | 1320 | MPa | ASTM D638 |
| tensile strength | |||
| fracture | 20.7 | MPa | ASTM D638 |
| Tensile strain | |||
| fracture | 85 | % | ASTM D638 |
| Bending modulus | 1170 | MPa | ASTM D790 |
| bending strength | |||
| fracture | 33.1 | MPa | ASTM D790 |
| Taber abraser | ASTM D1044 | ||
| 100 cycles, 500 g | 0.00100 | mg | ASTM D1044 |
| 500 cycles, 500 g | 0.0105 | mg | ASTM D1044 |
| 1000 cycles, 500 g | 0.0165 | mg | ASTM D1044 |
| 2000 cycles, 500 g | 0.0355 | mg | ASTM D1044 |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Rate A (50°C/h), Loading 1 (10 N) |
| 3. Rate A (50°C/h), Loading 2 (50 N) |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |