| About |
|---|
| Liquid silicone rubber material for outdoor medium and high voltage resistance terminal Product Description 2-part liquid silicone rubber, which is particularly suitable for injection molding with tracking resistance 1A 3.5 grade, mixing ration of parts A:B=1:1, catalyzed by platinum. The appearance of A is transparent and B is grey. Key Features Injection molding High tear strength High elongation Low tension set Rapid vulcanization Excellent tracking resistance At the temperature of 20 and in the condition of air-proof, the shelf life is 5 days after mixing A and B, the shelf life will decrease with the increasing of the temperature. Applications Medium voltage cable accessories and Cable connectors Indoor and outdoor cold shrink terminals&& |
| Product Description | |
|---|---|
| Supplier | SQUARE |
| Generic | 硅橡胶,LSR |
| Material Status | Commercial: Active |
| Features | Good Tensile Strength,Good tear strength,Fast Cure,Electric mark |
| Availabilitys | Africa & Middle East ,North America,Latin America,Asia Pacific,Europe |
| Process Methods | Liquid injection molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.13 | g/cm³ | ASTM D792 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | |||
| Shaw’s A | 35 | ASTM D2240 |
| elastic body | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile permanent deformation | |||
| 300% strain, 120 ℃ | 8 | % | ASTM D412 |
| tensile strength | 9.00 | MPa | ASTM D412 |
| Tensile strain | |||
| fracture | 800 | % | ASTM D412 |
| tear strength | 30.0 | kN/m | ASTM D624 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volume resistivity | 1.9E+14 | ohms·cm | IEC 60093 |
| Dielectric constant | |||
| 50 Hz | 2.80 | IEC 60250 | |
| Dissipation factor | |||
| 50 Hz | 1.6E-3 | IEC 60250 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Thermosetting components | |||
| Component A | 按重量计算的混合比: 1.0 | ||
| Component B | 按重量计算的混合比: 1.0 | ||
| storage stability | |||
| 20 ℃ | 7200 | min | |
| Storage period | 52 | wk |
| Uncured Properties | Nominal value | Unit | Test method |
|---|---|---|---|
| colour | |||
| — | Clear/Transparent | ||
| — | Grey | ||
| Solid content | 100 | % | |
| viscosity | 850 | Pa·s |
| Cured Properties | Nominal value | Unit | Test method |
|---|---|---|---|
| Tracking Resistance | 1A3.5 | IEC 60587 |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Die C |
| 3. 15hrs |
| 4. Die B |
| 5. Part A |
| 6. Part B |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |