| About |
|---|
| Staramide BS6 is a 30 % Glass Bead Reinforced Polyamide 6 Injection Molding Resin&& |
| Product Description | |
|---|---|
| Generic | PA6 |
| Material Status | Commercial: Active |
| Availabilitys | Africa & Middle East ,North America,Latin America,Asia Pacific,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.35 | g/cm³ | ISO 1183 |
| Shrinkage rate | |||
| MD | 1.0 – 1.5 | % | ISO 294-4 |
| Water absorption rate | |||
| 23°C，饱和 | 6.5 | % | ISO 62 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | |||
| 23℃，5 mm/min | 65.0 | MPa | ISO 527-2 |
| Tensile strain | |||
| Fracture, 23 ℃, 5 mm/min | 10 | % | ISO 527-2 |
| Tensile modulus | |||
| 23℃，1 mm/min | 4200 | MPa | ISO 527-2 |
| bending strength | |||
| 2 mm/min，23℃ | 108 | MPa | ISO 178 |
| Bending modulus | |||
| 2 mm/min，23℃ | 4100 | MPa | ISO 178 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 0.45 MPa, unannealed | 195 | ℃ | ISO 75-2/Bf |
| 1.8 MPa, annealed | 85.0 | ℃ | ISO 75-2/Af |
| Vicat Softening Temp | |||
| Linear coefficient of thermal expansion | |||
| MD | 5.0E-5 | 1/℃ | ISO 11359-2 |
| TD | 6.0E-5 | 1/℃ | ISO 11359-2 |
| B120 | 215 | ℃ | ISO 306/B120 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | |||
| 1.60 mm | HB | UL-94 | |
| Extreme oxygen index | 24 | % | ISO 4589-2 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | |||
| 23℃ | 5.00 | kJ/m² | ISO 180-1A |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 75.0 -85.0 | °C | |
| Drying time | 4.00 – 6.00 | Hr | |
| Water content | 0.20 | % | |
| Injection temperature | |||
| Rear barrel temperature | 230-240 | °C | |
| Central temperature of the barrel | 240-250 | °C | |
| Barrel front temperature | 240-270 | °C | |
| Die temperature | 240-270 | °C | |
| Mold temperature | 60.0-80.0 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 0.079 in/min |
| 3. at Break |
| 4. 120x10x4 mm |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |