Starflam® 525K NT0779

About
Starflam 525K NT0779 (formerly Vydyne® ECO525K NT0779) is a non-halogenated flame retardant, PA66 grade modified with 25% glass fiber for improved stiffness and strength.

Product Description
Supplier	Ascend
Generic	PA66
Material Status	Commercial: Active
Features	Low density,processability,Good Dimensional Stability,Heat Resistance, Good,Good heat aging resistance,Corrosion Resistant,Flame Characteristics,High strength
Availabilitys	Asia Pacific,North America,Europe

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	1.40	g/cm³	ISO 1183
Molding Shrinkage			ISO 294-4
Across Flow : 23°C, 2.00 mm	1.1	%	ISO 294-4
Flow : 23°C, 2.00 mm	0.3	%	ISO 294-4
Water Absorption			ISO 62
23°C, 24 hr	1	%	ISO 62
Equilibrium, 23°C, 50% RH	1.9	%	ISO 62

MECHANICAL	Nominal value	Unit	Test method
Tensile Modulus (23°C)	8687.4	mpa	ISO 527-2
Tensile Stress (Break, 23°C)	131.7	mpa	ISO 527-2
Tensile Strain (Break, 23°C)	3.1	%	ISO 527-2
Flexural Modulus (23°C)	9101.1	mpa	ISO 178
Flexural Strength (23°C)	208.2	mpa	ISO 178

IMPACT	Nominal value	Unit	Test method
Charpy Notched Impact Strength			ISO 179/1eA
+23°C	4.76	ftlb/in²	ISO 179/1eA
-30°C	4.52	ftlb/in²	ISO 179/1eA
-40°C	4.52	ftlb/in²	ISO 179/1eA
Charpy Unnotched Impact Strength			ISO 179/1eU
+23°C	32.3	ftlb/in²	ISO 179/1eU
-30°C	31.4	ftlb/in²	ISO 179/1eU
-40°C	30	ftlb/in²	ISO 179/1eU
Notched Izod Impact Strength			ISO 180/1A
+23°C	4.57	ftlb/in²	ISO 180/1A
-30°C	4.33	ftlb/in²	ISO 180/1A
-40°C	4.33	ftlb/in²	ISO 180/1A

THERMAL	Nominal value	Unit	Test method
Heat Deflection Temperature			ISO 75-2/A
1.80 MPa, Unannealed	239	℃	ISO 75-2/A
0.45 MPa, Unannealed	257	℃	ISO 75-2/B
Melting Temperature	260	℃	ISO 11357-3
CLTE			ISO 11359-2
Flow : 23 to 55°C, 2.00 mm	23	E-6/K	ISO 11359-2
Transverse : 23 to 55°C, 2.00 mm	67	E-6/K	ISO 11359-2
RTI Elec			UL 746
0.200 mm	140	℃	UL 746
0.400 mm	140	℃	UL 746
0.750 mm	140	℃	UL 746
1.50 mm	140	℃	UL 746
3.00 mm	140	℃	UL 746
RTI Imp			UL 746
0.200 mm	95	℃	UL 746
0.400 mm	110	℃	UL 746
0.750 mm	120	℃	UL 746
1.50mm	130	℃	UL 746
3.00 mm	130	℃	UL 746
RTI Str			UL 746
0.200 mm	115	℃	UL 746
0.400 mm	130	℃	UL 746
0.750 mm	140	℃	UL 746
1.50 mm	150	℃	UL 746
3.00 mm	150	℃	UL 746

Electrical performance	Nominal value	Unit	Test method
Dielectric Strength (1.00 mm)	1070	kV/in	IEC 60243
Comparative Tracking Index (3.00 mm)	600	V	IEC 60112
High Amp Arc Ignition (HAI)			UL 746
0.400 mm	PLC0	–	UL 746
0.750 mm	PLC0	–	UL 746
1.50 mm	PLC0	–	UL 746
3.00 mm	PLC0	–	UL 746
Hot-wire Ignition (HWI)			UL 746
0.400 mm	PLC2	–	UL 746
0.750 mm	PLC1	–	UL 746
1.50 mm	PLC0	–	UL 746
3.00 mm	PLC0	–	UL 746

Process Conditions
Injection Molding	Nominal value	Unit	Test method
Drying Temperature	80	℃
Drying Time	4-6	h
Rear Temperature	275-300	℃
Middle Temperature	275-300	℃
Front Temperature	275-300	℃
Nozzle temperature	275-300	℃
Processing (Melt) Temperature	275-300	℃
Mold Temperature	60-120	℃

Notes
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.