| About |
|---|
| Starflam M10004A is an Unfilled Halogen Free Flame Retardant PP Injection Molding Resin&& |
| Product Description | |
|---|---|
| Supplier | Ascend |
| Generic | PP not specified |
| Material Status | Commercial: Active |
| Features | Halogen free,V-0,Flame Characteristics |
| Availabilitys | Asia Pacific,North America,Africa & Middle East ,Latin America,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.02 | g/cm³ | ISO 1183 |
| Shrinkage rate | |||
| MD：4.0 mm | 1.8 | % | Internal Method |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | 2300 | MPa | ISO 527-1-2 |
| tensile strength | |||
| yield | 29.0 | MPa | ISO 527-2/50 |
| Tensile strain | |||
| yield | 4.2 | % | ASTM D638 |
| Bending modulus | 2100 | MPa | ISO 178 |
| bending strength | 44.0 | MPa | ISO 178 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | |||
| 23℃ | 4.0 | kJ/m² | ISO 180-1A |
| Notched impact strength of cantilever beam | |||
| 23℃ | 15 | kJ/m² | ISO 180/1U |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed, 64 mm span | 68.0 | ℃ | ISO 75-2/Af |
| Linear coefficient of thermal expansion | ISO 11359-2 | ||
| MD：23~60℃ | 1.1E-4 | 1/℃ | ISO 11359-2 |
| TD：23~60℃ | 1.1E-4 | 1/℃ | ISO 11359-2 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| 1.60 mm, E2P measurement | V-0 | UL 94 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 70 | °C | |
| Drying time | 3.0 | hr | |
| Barrel rear temperature | 180 to 190 | °C | |
| Barrel middle temperature | 190 to 200 | °C | |
| Barrel front temperature | 190 to 200 | °C | |
| Processing (melt) temperature | 190 to 200 | °C | |
| Mold temperature | 30 to 50 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 2.0 in/min |
| 3. 0.079 in/min |
| 4. at Yield |
| 5. 80x10x4 mm |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |