| About |
|---|
| Stat-Rite® S-680 is a static dissipative PETG alloy. Stat-Rite® S-680 utilizes the patented Stat-Rite® inherently dissipative polymer (IDP) alloy system to provide clean, permanent ESD protection. Stat-Rite® IDP alloys provide consistent static dissipation even when thermoformed or injection molded into components. FEATURES Permanently static dissipative Humidity Independent Ultra clean: low out-gassing, low extractable ionics Durable: can be used for years APPLICATIONS Hard disk drive component packaging Electronic component packaging Medical device packaging&& |
| Product Description | |
|---|---|
| Supplier | Lubrizol Advanced Materials |
| Generic | PETG |
| Material Status | Commercial: Active |
| Features | Low extract,High purity,Rapid Static Decay,Low (to None) Ion Content,Electrostatic discharge protection,Low odor,Durability,Antistatic property |
| Availabilitys | North America,Latin America,Asia Pacific,Europe |
| Process Methods | Thermo forming |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.25 | g/cm³ | ASTM D792 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | 1100 | MPa | ASTM D638 |
| tensile strength | |||
| yield | 28.3 | MPa | ASTM D638 |
| Tensile strain | |||
| fracture | 350 | % | ASTM D638 |
| Bending modulus | 1240 | MPa | ASTM D790 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | 960 | J/m | ASTM D256 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | ASTM D648 | ||
| 0.45 MPa, unannealed | 60.0 | ℃ | |
| 1.8 MPa, unannealed | 55.0 | ℃ |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volume resistivity | 5.0E+9 | ohms·cm | ASTM D257 |
| Electrostatic attenuation | |||
| 1000V to10V，50% R.H. | 0.3 | sec | CPM |
| -5000V to -50V | 0.0100 | sec | CPM |
| 5000V to 50V，12% R.H. | 0.0100 | sec | FTMS 101C |
| Surface resistance | |||
| 12% R.H. | 5.0E+8 | ohms | ESD S11.11 |
| Surface resistivity | |||
| 50% RH | 2.0E+9 | ohms/sq | ASTM D257 |
| Tribocharge（Nitrile Glove） | 10.0 | V | Internal Method |
| Supplementary information | Nominal value | Unit | Test method |
|---|---|---|---|
| Ion content | Internal Method | ||
| Cl Anion | 5.00 | ng/cm² | |
| F Anion | 2.00 | ng/cm² | |
| NO3 Anion | 3.00 | ng/cm² | |
| PO4 Anion | 2.00 | ng/cm² | |
| SO4 Anion | 5.00 | ng/cm² | |
| Outgassing | Internal Method | ||
| MMA | 0.800 | µg/g | |
| Styrene | 0.100 | µg/g | |
| Toluene | 0.300 | µg/g | |
| Total Organics | 4.00 | µg/g | |
| nonvolatile content | 0.500 | µg/cm² | Internal Method |
| Filler | IDP Alloy |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Test Method #3010-4 |
| 3. Test Method #3010-5 |
| 4. Test Method #3010-3 |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |