| About |
|---|
| STYRON™ 666H is a general purpose polystyrene with easy flow and good clarity. It is recommended for applications where a specific balance of flow and strength are important. Applications: Media enclosures Disposable cups Blending with HIPS Complies with: U.S. FDA 21 CFR 177.1640 Consult the regulation for complete details.&& |
| Product Description | |
|---|---|
| Supplier | Trinseo |
| Generic | PS (GPPS) |
| Material Status | Commercial: Active |
| Features | Good Rigidity,Good Clarity,Good liquidity,HB |
| Availabilitys | Asia Pacific |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.04 | g/cm³ | ASTM D792 |
| Melt Flow Rate | |||
| 200℃，5.0kg | 8.0 | g/10min | ASTM D1238 |
| Shrinkage rate | |||
| MD | 0.40 to 0.70 | % | ASTM D955 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | ASTM D638 | ||
| Compression Molding | 3200 | MPa | ASTM D638 |
| injection molding | 3300 | MPa | ASTM D638 |
| tensile strength | ASTM D638 | ||
| Yield, molding | 40.0 | MPa | ASTM D638 |
| Yield, injection molding | 47.6 | MPa | ASTM D638 |
| Limit, molded | 40.0 | MPa | ASTM D638 |
| Extreme, injection molding | 47.6 | MPa | ASTM D638 |
| Tensile strain | ASTM D638 | ||
| Fracture, molded | 1.0 | % | ASTM D638 |
| Fracture, injection molding | 2.0 | % | ASTM D638 |
| Bending modulus | ASTM D790 | ||
| Compression Molding | 3100 | MPa | ASTM D790 |
| injection molding | 3240 | MPa | ASTM D790 |
| bending strength | ASTM D790 | ||
| Compression Molding | 56.5 | MPa | ASTM D790 |
| injection molding | 89.6 | MPa | ASTM D790 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | ASTM D256 | ||
| 23 ℃, molded | 11 | J/m | ASTM D256 |
| 23 ℃, injection molding | 16 | J/m | ASTM D256 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | ASTM D648 | ||
| 1.8 MPa, unannealed | 76.1 | ℃ | ASTM D648 |
| 1.8 MPa, annealed | 93.9 | ℃ | ASTM D648 |
| Vicat Softening Temp | 99.0 | ℃ | ASTM D1525 |
| Linear coefficient of thermal expansion | |||
| MD | 7.6E-5 | 1/℃ | ASTM D696 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | |||
| 1.50 mm | HB | UL 94 |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. This rating not intended to reflect hazards presented by this or any other material under actual fire conditions. |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |