| About |
|---|
| STYRON A-TECH™ 1110 advanced technology polystyrene resin is a high-gloss, high-impact resin for injection molding applications. Main Characteristics: Excellent toughness High gloss Applications: Small appliances Toys Printers Remote controls Complies with: U.S. FDA 21 CFR 177.1640 Consult the regulation for complete details.&& |
| Product Description | |
|---|---|
| Supplier | Trinseo |
| Generic | PS (HIPS) |
| Material Status | Commercial: Active |
| Features | Good flexibility,Good surface appearance,High impact resistance,HB |
| Availabilitys | Asia Pacific |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | |||
| — | 1.04 | g/cm³ | ASTM D792 |
| — | 1.03 | g/cm³ | ISO 1183-3 |
| Melt Flow Rate | |||
| 200℃，5.0kg | 3.0 | g/10min | ASTM D1238 |
| Melt Volume Rate | |||
| 200℃，5 kg | 4.00 | cm³/10min | ISO 1133 |
| Shrinkage rate | |||
| MD | 0.40 to 0.70 | % | ASTM D955 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | |||
| Compression Molding | 1750 | MPa | ASTM D638 |
| injection molding | 1860 | MPa | ASTM D638 |
| — | 1770 | MPa | ISO 527-2 3 |
| tensile strength | |||
| Yield, molding | 20.7 | MPa | ASTM D638 |
| Yield, injection molding | 22.8 | MPa | ASTM D638 |
| yield | 25.0 | MPa | ISO 527-2 3 |
| Fracture, molded | 14.5 | MPa | ASTM D638 |
| Fracture, injection molding | 19.3 | MPa | ASTM D638 |
| Tensile strain | |||
| yield | 1.5 | % | ISO 527-2 3 |
| Fracture, molded | 30 | % | ASTM D638 |
| Fracture, injection molding | 50 | % | ASTM D638 |
| Tensile strain | |||
| fracture | > 50 | % | ISO 527-2 3 |
| Bending modulus | ASTM D790 | ||
| Compression Molding | 1900 | MPa | ASTM D790 |
| injection molding | 2140 | MPa | ASTM D790 |
| bending strength | ASTM D790 | ||
| Compression Molding | 38.3 | MPa | ASTM D790 |
| injection molding | 44.8 | MPa | ASTM D790 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | ISO 179/1eA 3 | ||
| -30℃ | 4.00 | kJ/m² | ISO 179/1eA 3 |
| 23℃ | 18.0 | kJ/m² | ISO 179/1eA 3 |
| Charpy impact strength | ISO 179/1eU 3 | ||
| -30℃ | 60.0 | kJ/m² | ISO 179/1eU 3 |
| 23℃ | 125 | kJ/m² | ISO 179/1eU 3 |
| Impact strength of cantilever beam notch | ASTM D256 | ||
| 23 ℃, molded | 130 | J/m | ASTM D256 |
| 23 ℃, injection molding | 240 | J/m | ASTM D256 |
| Drop hammer impact | |||
| 23℃ | 33.9 | J | ASTM D3029 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 0.45 MPa | 87.0 | ℃ | ISO 75-2 3 |
| 1.8 MPa, unannealed | 72.8 | ℃ | ASTM D648 |
| 1.8 MPa, annealed | 92.8 | ℃ | ASTM D648 |
| 1.8 MPa | 76.0 | ℃ | ISO 75-2 3 |
| Vicat Softening Temp | |||
| — | 102 | ℃ | ASTM D1525 |
| B50 | 88.0 | ℃ | ISO 306 3 |
| Linear coefficient of thermal expansion | |||
| MD | |||
| — | 7.6E-5 | cm/cm/℃ | ASTM D696 |
| — | 8.6E-5 | cm/cm/℃ | ISO 11359-2 3 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | |||
| 1.50 mm | HB | UL 94 | |
| Flame retardant level | |||
| 3.10 mm | HB | ISO 1210 3 |
| optical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| gloss | |||
| 60° | 92 | ASTM D523 |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Tested in accordance with ISO 10350. 23°C/50%r.h. unless otherwise noted. |
| 3. This rating not intended to reflect hazards presented by this or any other material under actual fire conditions. |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |