| About |
|---|
| Polyphenylene Sulfide (Abbr. PPS) is a high performance thermoplastic polymer, offers excellent heat resistance, abrasion and radiation resistances, flame retardant, average mechanical properties, excellent dimensional stability and electrical properties. With all these outstanding properties, PPS compounded materials have already replace some of the metals as structural materials, and widely used in electronic and electrical, automotive, mechanical and chemical, aerospace, and military fields.&& |
| Product Description | |
|---|---|
| Supplier | Asia International Enterprise (Hong Kong) |
| Generic | PPS+PA |
| Material Status | Commercial: Active |
| Features | Good Dimensional Stability,Good Electrical Properties,Gamma radiation,Flame Characteristics,High Heat Resistance,Good wear resistance,V-0 |
| Availabilitys | Africa & Middle East ,North America,Latin America,Asia Pacific,Europe |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.70 | g/cm³ | ISO 1183 |
| Shrinkage rate | ISO 294-4 | ||
| TD | 0.50 | % | |
| MD | 0.30 | % | |
| Water absorption rate | |||
| Saturation, 23 ℃ | 0.090 | % | ISO 62 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | |||
| yield | 170 | MPa | ISO 527-2/1270 |
| Tensile strain | |||
| fracture | 1.7 | % | ISO 527-2/50 |
| Bending modulus | 12500 | MPa | ISO 178 |
| bending strength | 220 | MPa | ISO 178 |
| friction coefficient | 0.32 | ISO 8295 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | 13 | kJ/m² | ISO 180 |
| Notched impact strength of cantilever beam | 55 | kJ/m² | ISO 180 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed | > 250 | ℃ | ISO 75-2/A |
| Linear coefficient of thermal expansion | |||
| MD：-20~150℃ | 1.8E-4 | 1/℃ | ISO 11359-2 |
| Thermal conductivity coefficient | 0.33 | W/m/K | ISO 8302 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volume resistivity | > 1.0E+16 | ohms·cm | IEC 60093 |
| Dielectric strength | |||
| In oil | 22 | kV/mm | IEC 60243-1 |
| Dielectric constant | |||
| 1 MHz | 3.80 | IEC 60250 | |
| Dissipation factor | |||
| 1 MHz | 9.0E-3 | IEC 60250 | |
| Compared to the leakage tracing index | 150 | V | IEC 60112 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| 1.60 mm | V-0 | UL 94 |
| Notes |
|---|
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |