| About |
|---|
| TAISOX® 2110 is a Linear Low Density Polyethylene material. It is available in Asia Pacific, Europe, or North America for blown film. Important attributes of TAISOX® 2110 are: Antiblock Good Sealability Good Tear Strength High Strength Impact Resistant Typical application of TAISOX® 2110: Film&& |
| Product Description | |
|---|---|
| Supplier | fpc-tw |
| Generic | Linear low density polyethylene |
| Material Status | Commercial: Active |
| Features | Good Rigidity,Good heat sealing,High impact resistance,Low density,Good tear strength |
| Availabilitys | North America,Asia Pacific,Europe |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 0.918 | g/cm³ | ASTM D1505 |
| Melt Flow Rate | |||
| 190℃，2.16kg | 1.0 | g/10min | ASTM D1238 |
| film | Nominal value | Unit | Test method |
|---|---|---|---|
| film thickness | |||
| test | 38 | µm | |
| Secant modulus | ASTM D882 | ||
| 1% secant, MD: 38 µ m, blow molded film | 157 | MPa | ASTM D882 |
| 1% secant, TD: 38 µ m, blow molded film | 196 | MPa | ASTM D882 |
| tensile strength | ASTM D882 | ||
| MD, yield, 38 µ m, blow molded film | 9.81 | MPa | ASTM D882 |
| TD, yield, 38 µ m, blow molded film | 10.8 | MPa | ASTM D882 |
| MD, fracture, 38 µ m, blow molded film | 49.0 | MPa | ASTM D882 |
| TD, fracture, 38 µ m, blow molded film | 44.1 | MPa | ASTM D882 |
| Tensile strain | ASTM D882 | ||
| MD, fracture, 38 µ m, blow molded film | 620 | % | ASTM D882 |
| TD, fracture, 38 µ m, blow molded film | 810 | % | ASTM D882 |
| Drop hammer impact | |||
| 38 µ m, blow molded film | 610 | g | ASTM D1709 |
| Elmandorf tear strength | ASTM D1922 | ||
| MD: 38 µ m, blow molded film | 460 | g | ASTM D1922 |
| TD: 38 µ m, blow molded film | 760 | g | ASTM D1922 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Embrittlement temperature | -70.0 | ℃ | ASTM D746 |
| Vicat Softening Temp | 93.0 | ℃ | ASTM D1525 |
| Melting temperature | 121 | ℃ |
| optical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| gloss | |||
| 45 °, 38 µ m, blow molded film | 51 | ASTM D2457 | |
| transparency | 65.0 | ASTM D1746 | |
| Haze | |||
| 38 µ m, blow molded film | 13 | % | ASTM D1003 |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |