| About |
|---|
| Basic&& |
| Product Description | |
|---|---|
| Supplier | Idemitsu |
| Generic | Polycarbonate |
| Material Status | Commercial: Active |
| Features | HB |
| Availabilitys | Africa & Middle East ,North America,Latin America,Asia Pacific,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.27 | g/cm³ | ISO 1183 |
| Spiral flow length | 21.0 | cm | Internal Method |
| Shrinkage rate | Internal Method | ||
| TD：2.0 mm | 0.60 | % | Internal Method |
| MD：2.0 mm | 0.40 | % | Internal Method |
| Water absorption rate | |||
| Equilibrium, 23 ℃, 50% RH | 0.15 | % | ISO 62 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | |||
| 23℃ | 8.0 | kJ/m² | ISO 179 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed | 142 | ℃ | ISO 75-2/A |
| Linear coefficient of thermal expansion | |||
| MD | 4.5E-5 | 1/℃ | ISO 11359-2 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volume resistivity | > 1.0E+16 | ohms·cm | ASTM D257 |
| Dielectric strength | > 22 | kV/mm | IEC 60243-1 |
| Dielectric constant | |||
| 1 MHz | 2.95 | IEC 60250 | |
| Dissipation factor | |||
| 1 MHz | 9.0E-3 | IEC 60250 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| 0.70 mm | HB | UL 94 |
| Supplementary information | Nominal value | Unit | Test method |
|---|---|---|---|
| ISO Shortname | >PC-GF10< |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | |||
| yield | 80.0 | MPa | ISO 527-2 |
| Nominal tensile fracture strain | 5.0 | % | ISO 527-2 |
| Bending modulus | 3500 | MPa | ISO 178 |
| bending strength | 120 | MPa | ISO 178 |
| Rockwell hardness | |||
| M-level | 65 | ISO 2039-2 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 120 | °C | |
| Drying time | 5.0 to 8.0 | hr | |
| Barrel rear temperature | 260 to 300 | °C | |
| Barrel middle temperature | 260 to 300 | °C | |
| Barrel front temperature | 260 to 300 | °C | |
| Mold temperature | 80 to 120 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Mold Temperature: 176°F, Melt Temperature: 536°F, Injection Pressure: 1.81E+4 psi |
| 3. Thickness: 2mm / Width: 10mm |
| 4. 24h |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |