| About |
|---|
| Product Description | |
|---|---|
| Supplier | Idemitsu |
| Generic | Polycarbonate |
| Material Status | Commercial: Active |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Shrinkage rate | |||
| TD：1.6 mm | 0.6 | % | ASTM D955 |
| MD：1.6 mm | 0.2 | % | ASTM D955 |
| Density | 1.330 | g/cm³ | ISO 1183 B |
| Spiral flow length | 27 | cm | Idemitsu Method |
| Water absorption rate | |||
| 23℃，24hr，60% RH | 0.13 | % | ISO 62 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | |||
| fracture | 110 | MPa | ISO 527 |
| yield | 110 | MPa | ISO 527 |
| Nominal tensile fracture strain | 4 | % | ISO 527 |
| Tensile modulus | 5.800 | Mpa | ISO 527 |
| bending strength | 160 | MPa | ISO 178 |
| Bending modulus | 5.900 | MPa | ISO 178 |
| Rockwell hardness | 70 | R/M 级 | ISO 2039 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa | 145 | ℃ | ISO 75 A |
| Linear coefficient of thermal expansion | 2.5 | x 10 -5 cm/cm/ºC | ASTM D 696 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Relative permittivity | 2.95 | 1 MHz | IEC 60250 |
| Relative permittivity | 3.10 | 100 Hz | IEC 60250 |
| Dielectric strength | |||
| 1.6 mm | >22E+5 | kV/mm | IEC 60243-1 |
| Dissipation factor | 0.0092 | 1 MHz | IEC 250 |
| Dissipation factor | 8 x 10^-4 | 100 Hz | IEC 250 |
| Arc resistance | 110 | sec | ASTM D495 |
| Volume resistivity | >10^16 | ohms·cm | IEC 60093 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | V-2 | 1.5mm | UL 94 |
| Extreme oxygen index | 32 | % | ASTM D2863 |
| Igniting temperature of the hot wire | |||
| 2 mm | 850 | ℃ | IEC 60695-2-13 |
| Igniting temperature of the hot wire | |||
| 3 mm | 875 | ℃ | IEC 60695-2-13 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Unnotch Impact strength | |||
| 23℃ | 13 | kJ/m² | ISO 179 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Melt temperature | 280 ~ 305 | °C | |
| Mold temperature | 80 ~ 120 | °C | |
| Pre-drying | 4 hours/120°C | ||
| Notes |
|---|
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |