| About |
|---|
| Medium viscosity polyamide 6 grade, without any additives.&& |
| Product Description | |
|---|---|
| Generic | PA6 |
| Material Status | Commercial: Active |
| Features | Food contact compliance |
| Availabilitys | Africa & Middle East ,North America,Latin America,Asia Pacific,Europe |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.14 | g/cm³ | ISO 1183 |
| Shrinkage rate | |||
| MD | 0.014 | % | ISO 294-4 |
| TD | 0.014 | % | ISO 294-4 |
| Water absorption rate | |||
| 23℃，24hr | 1.8 | % | ISO 62 |
| Melt Flow Rate | |||
| 275℃，5.0kg | 120 | g/10min | ISO 1133 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, annealed | 60 | ℃ | ISO 75-2/A |
| Hot deformation temperature | 50 | ℃ | ISO 75 |
| Melting temperature | 221 | ℃ | ISO 11357-3 |
| Glowing wire flammability index | 750 | ℃ | PN-EN-60695-2-12 |
| Vicat Softening Temp | |||
| B50 | 195 | ℃ | ISO 306/A50 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volumetric resistance | 1.0E+15 | Ω.cm | IEC 60093 |
| Surface resistance | 1.0E+15 | Ω.cm | IEC 60093 |
| Insulation strength | |||
| 30 | KV/mm | IEC 60243-1 | |
| Dissipation factor | |||
| Compared to the leakage tracing index | 600 | V | IEC 60112 |
| Volumetric resistance | 1.0E+12 | Ω.cm | IEC 60093 |
| Surface resistance | 1.0E+13 | Ω.cm | IEC 60093 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | |||
| 1.6mm | V-2 | UL 94 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Unnotch Impact strength | |||
| 23℃ | NB | kJ/m² | ISO 179/1eU |
| Charpy Notched Impact Strength | |||
| 23℃ | 5 | kJ/m² | ISO 179/1eA |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| 60 | MPa | ISO 2039-1 | |
| 140 | MPa | ISO 2039-1 | |
| tensile strength | |||
| Yield, 23 ℃ | 78 | MPa | ISO 527-2 |
| Tensile strain | |||
| Fracture, 23 ℃ | 50 | % | ISO 527-2 |
| bending strength | |||
| 23℃ | 82 | MPa | ISO 178 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 75 -100 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 0.079 in/min |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |