| About |
|---|
| TECANYL®, due to its inherent chemical composition, exhibits unusually low moisture absorption. Therefore, good electrical insulating properties are realized over a wide range of humidity and temperature conditions. Chemical attack from water, most salt solutions, acids and bases is also minimal with TECANYL®. The addition of glass fiber reinforcement enhances both the mechanical and thermal properties of the basic TECANYL® material. Made from Noryl® EN265 resin. Made from Noryl EN265 resin® exhibits a broad range of outstanding properties for applications in computers and business equipment, automotive, electrical insulation, telecommunications, appliances, electronics, and many other industries. Good electrical insulating properties Long-term dimensional stability Superior impact strength TECANYL® exhibits a continuous use temperature in excess of 220°F Wide range of UL flammability ratings from Light weight Thermoformable capability Possesses good hydrolytic stability&& |
| Product Description | |
|---|---|
| Supplier | Ensinger |
| Generic | PPO(PPE) |
| Material Status | Commercial: Active |
| Features | High impact resistance,Good Dimensional Stability,Hydrolysis stability,Low moisture absorption,Insulation |
| Availabilitys | North America |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.08 | g/cm³ | ASTM D792 |
| Water absorption rate | |||
| 23℃，24hr | 0.070 | % | ASTM D570 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | |||
| 23℃ | 190 | J/m | ASTM D256 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 0.45 MPa, unannealed | 137 | ℃ | |
| 1.8 MPa, unannealed | 123 | ℃ | |
| Vicat Softening Temp | 154 | ℃ | ASTM D1525 |
| Linear coefficient of thermal expansion | |||
| MD | 5.9E-5 | 1/℃ | ASTM D696 |
| Operating temperature | |||
| Intermittent | 110 | ℃ | |
| long-term | 104 | ℃ |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volume resistivity | 1.0E+17 | ohms·cm | ASTM D257 |
| Dielectric strength | 20 | kV/mm | ASTM D149 |
| Dielectric constant | |||
| 23 ℃，60 Hz | 2.70 | ASTM D150 | |
| Dissipation factor | |||
| 23℃，60 Hz | 7.0E-4 | ASTM D150 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | V-1 | UL 94 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Rockwell hardness | |||
| R-level | 119 | ASTM D785 | |
| Tensile modulus | |||
| 23℃ | 2410 | MPa | ASTM D638 |
| tensile strength | |||
| Yield, 23 ℃ | 62.1 | MPa | |
| Fracture, 23 ℃ | 63.4 | MPa | |
| Tensile strain | |||
| Fracture, 23 ℃ | 25 | % | ASTM D638 |
| Bending modulus | |||
| 23℃ | 2550 | MPa | ASTM D790 |
| bending strength | |||
| 23℃ | 92.4 | MPa | ASTM D790 |
| friction coefficient | |||
| dynamic | 0.39 | ||
| static state | 0.32 |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 40 psi, 50 fpm |
| 3. 50% RH |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |