TECAPEEK® CF30

About
TECAPEEK® CF30 is a 30% carbon filled version of Ensinger’s standard TECAPEEK which offers improved strength and stiffness as well as greater load bearing capabilities for those applications that require it. TECAPEEK™s exceptional property profile enables it to be utilized in many of the most critical areas in general industry, as well as in the automotive, marine, nuclear, oil well, electronics, medical and aerospace fields. Extremely high thermal and mechanical capabilities Very high continuous working temperature Increased stiffness and bearing properties Excellent abrasion and wear resistance A superior dielectric at high temperatures and frequencies Exceptional chemical resistance Very high level of dimensional stability Inherently low flammability rating – UL94 (V-0) Excellent hydrolysis resistance&&

About

TECAPEEK® CF30 is a 30% carbon filled version of Ensinger’s standard TECAPEEK which offers improved strength and stiffness as well as greater load bearing capabilities for those applications that require it. TECAPEEK™s exceptional property profile enables it to be utilized in many of the most critical areas in general industry, as well as in the automotive, marine, nuclear, oil well, electronics, medical and aerospace fields. Extremely high thermal and mechanical capabilities Very high continuous working temperature Increased stiffness and bearing properties Excellent abrasion and wear resistance A superior dielectric at high temperatures and frequencies Exceptional chemical resistance Very high level of dimensional stability Inherently low flammability rating – UL94 (V-0) Excellent hydrolysis resistance&&

Product Description
Supplier	Ensinger
Generic	PEEK
Material Status	Commercial: Active
Features	Good Dimensional Stability,Hydrolysis stability,High Heat Resistance,Good wear resistance,Solvent resistance,V-0
Availabilitys	North America

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	1.41	g/cm³	ASTM D792
Water absorption rate
23℃，24hr	0.060	%	ASTM D570

IMPACT	Nominal value	Unit	Test method
Impact strength of cantilever beam notch
23℃	48	J/m	ASTM D256

THERMAL	Nominal value	Unit	Test method
Hot deformation temperature
1.8 MPa, unannealed, 6.35 mm	316	℃	ASTM D648
Continuous use temperature	260	℃
Melting temperature	334	℃
Linear coefficient of thermal expansion
MD	1.4E-5	1/℃	ASTM D696
Thermal conductivity coefficient	0.92	W/m/K	ASTM C177

FLAME CHARACTERISTICS	Nominal value	Unit	Test method
Flame retardant level	V-0		UL 94

Supplementary information	Nominal value	Unit	Test method
Pressure limiting speed
1200 in/min，20℃	385000	psi·fpm

MECHANICAL	Nominal value	Unit	Test method
Rockwell hardness
M-level	107		ASTM D785
Tensile modulus
1% secant, 23 ℃	13000	MPa	ASTM D638
tensile strength
Yield, 23 ℃	186	MPa	ASTM D638
Tensile strain
Fracture, 23 ℃	1.1	%	ASTM D638
Bending modulus
23℃	12800	MPa	ASTM D790
bending strength
23℃	318	MPa	ASTM D790
compressive strength
23℃	240	MPa	ASTM D695
shear strength
23℃	97.2	MPa	ASTM D3846
friction coefficient	0.22

Notes
1. Typical properties: these are not to be construed as specifications.
2. 40 PSI, 50 FPM
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.