| About |
|---|
| TECAPEEK® GF30 is Ensinger’s 30% glass fiber reinforced TECAPEEK product. Made with Victrex 450 GL30 PEEK polymer, it offers enhanced mechanical and thermal properties over those of our basic TECAPEEK offering. It also offers excellent resistance in harsh chemical environments and is electrically insulative. TECAPEEK™s exceptional property profile enables it to be utilized in many of the most critical areas in general industry, as well as in the automotive, marine, nuclear, oil well, electronics, medical and aerospace fields.&& |
| Product Description | |
|---|---|
| Supplier | Ensinger |
| Generic | PEEK |
| Material Status | Commercial: Active |
| Features | Low smoke,Good Dimensional Stability,Hydrolysis stability,Gamma radiation,High Heat Resistance,Good wear resistance,Solvent resistance,Insulation,V-0 |
| Availabilitys | North America |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.53 | g/cm³ | ASTM D792 |
| Water absorption rate | |||
| 23℃，24hr | 0.11 | % | ASTM D570 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | |||
| 23℃ | 96 | J/m | ASTM D256 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed, 6.35 mm | 316 | ℃ | ASTM D648 |
| Continuous use temperature | 260 | ℃ | |
| Melting temperature | 334 | ℃ | |
| Linear coefficient of thermal expansion | |||
| MD | 2.2E-5 | 1/℃ | ASTM D696 |
| Thermal conductivity coefficient | 0.43 | W/m/K | ASTM C177 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Surface resistivity | 1.0E+16 | ohms | ASTM D257 |
| Volume resistivity | |||
| 23℃ | 1.0E+16 | ohms·cm | ASTM D257 |
| Dielectric strength | 6.9 | kV/mm | ASTM D149 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | V-0 | UL 94 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Rockwell hardness | |||
| M-level | 103 | ASTM D785 | |
| Tensile modulus | |||
| 1% secant, 23 ℃ | 9700 | MPa | ASTM D638 |
| tensile strength | |||
| Yield, 23 ℃ | 157 | MPa | ASTM D638 |
| Tensile strain | |||
| Fracture, 23 ℃ | 2.2 | % | ASTM D638 |
| Bending modulus | |||
| 23℃ | 10300 | MPa | ASTM D790 |
| bending strength | |||
| 23℃ | 233 | MPa | ASTM D790 |
| compressive strength | |||
| 23℃ | 215 | MPa | ASTM D695 |
| shear strength | |||
| 23℃ | 97.2 | MPa | ASTM D3846 |
| friction coefficient | 0.30 |
| Notes |
|---|
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |