TECATOR™ GF30

About
TECATOR is a high performance melt processable polyamide-imide that maintains its excellent mechanical and wear properties in temperature environments exceeding 500°F. TECATOR GF30 (XP142T) is a 30% glass filled grade, compression molded with superior stiffness and dimensional stability. It is available in a wide variety of custom tube, ring, rod and plate sizes. TECATOR™(PAI) typical applications: Pump parts, valve seats, piston rings, seal rings, engine transmission parts and bearing cages. For the semiconductor industry it is used for “burn in” test sockets, nests, chassis and other applications such as welding nozzle tips. Excellent weather and gamma radiation resistance Outstanding bearing and wear properties High strength and stiffness Excellent electrical values Good chemical resistance Maintains a high proportion of mechanical properties over a broad temperature spectrum – cryogenic to 500°F.&&

About

TECATOR is a high performance melt processable polyamide-imide that maintains its excellent mechanical and wear properties in temperature environments exceeding 500°F. TECATOR GF30 (XP142T) is a 30% glass filled grade, compression molded with superior stiffness and dimensional stability. It is available in a wide variety of custom tube, ring, rod and plate sizes. TECATOR™(PAI) typical applications: Pump parts, valve seats, piston rings, seal rings, engine transmission parts and bearing cages. For the semiconductor industry it is used for “burn in” test sockets, nests, chassis and other applications such as welding nozzle tips. Excellent weather and gamma radiation resistance Outstanding bearing and wear properties High strength and stiffness Excellent electrical values Good chemical resistance Maintains a high proportion of mechanical properties over a broad temperature spectrum – cryogenic to 500°F.&&

Product Description
Supplier	Ensinger
Generic	PAI
Material Status	Commercial: Active
Features	Good Rigidity,Weather resistance is good,Good Dimensional Stability,Good Electrical Properties,Gamma radiation,Good wear resistance,Solvent resistance
Availabilitys	North America

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	1.58	g/cm³	ASTM D792

IMPACT	Nominal value	Unit	Test method
Impact strength of cantilever beam notch
23℃	40	J/m	ASTM D256

THERMAL	Nominal value	Unit	Test method
Continuous use temperature	260	℃
Linear coefficient of thermal expansion
MD	3.8E-5	1/℃	ASTM D696

Electrical performance	Nominal value	Unit	Test method
Dielectric strength	18	kV/mm	ASTM D149
Dielectric constant			ASTM D150
1 MHz	3.80		ASTM D150
20.0 GHz	4.30		ASTM D150
30.0 GHz	4.40		ASTM D150
Dissipation factor			ASTM D150
1 MHz	6.0E-3		ASTM D150
20 GHz	5.0E-3		ASTM D150
30 GHz	8.0E-3		ASTM D150

MECHANICAL	Nominal value	Unit	Test method
Rockwell hardness
M-level	116		ASTM D785
tensile strength
Fracture, 23 ℃	117	MPa	ASTM D638
Tensile strain
Fracture, 23 ℃	2.0	%	ASTM D638
Bending modulus
23℃	5660	MPa	ASTM D790
bending strength
23℃	145	MPa	ASTM D790

Notes
1. Typical properties: these are not to be construed as specifications.
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

1. Typical properties: these are not to be construed as specifications.

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.