TECHNYL® A 50X1 GREY 2670 LP

About
TECHNYL® A 50X1 Grey 2670 LP is an unreinforced blend of polyamide 66 and 6 based on a non-phosphorous and non-halogenated flame retardant system, heat stabilized, for injection moulding. This flame retardant grade, UL94 V0 at 0.4mm, offers excellent filling qualities together with good stiffness. This grade has been designed to be laser printable.&&

Product Description
Supplier	DOMO
Generic	PA66/6
Material Status	Commercial: Active
Features	Low to no phosphorus content,Good stripping performance,Halogen free
Availabilitys	Africa & Middle East ,Asia Pacific,Europe
Process Methods	Injection Molding

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	1.16	g/cm³
Shrinkage rate
TD	0.72	%
MD	0.94	%
Water absorption rate
23℃，24hr	1.6	%

MECHANICAL	Nominal value	Unit
Tensile modulus
23℃	3650	MPa
tensile strength
Yield, 23 ℃	81.0	MPa
Fracture, 23 ℃	67.0	MPa
Tensile strain
Fracture, 23 ℃	19	%

IMPACT	Nominal value	Unit
Charpy Notched Impact Strength
23℃	4.5	kJ/m²
Charpy Unnotch Impact strength
23℃	85	kJ/m²

THERMAL	Nominal value	Unit
Hot deformation temperature
1.8 MPa, unannealed	70.0	℃
Melting temperature	257	℃

Electrical performance	Nominal value	Unit
Surface resistivity	1.0E+15	ohms
Volume resistivity	1.0E+15	ohms·cm
Dielectric strength
0.8 mm	34	kV/mm
Compared to the leakage tracing index
Solution A	600	V

FLAME CHARACTERISTICS	Nominal value	Unit
Flame retardant level
0.40 mm	V-0
0.80 mm	V-0
1.60 mm	V-0
3.20 mm	V-0
Glowing wire flammability index
0.80 mm	960	℃
1.6 mm	960	℃
3.2 mm	960	℃
Extreme oxygen index	33	%
French Fire Index	F2
French Smoke Index	I2

Supplementary information	Nominal value	Unit	Test method
European Railway Certification
R22	HL3
R23	HL3

Process Conditions
Injection	Nominal value	Unit	Test method
Injection instructions	Nominal value	Unit	Test method
drying temperature	80	°C
Recommended maximum moisture content	0.20	%
Temperature at the rear of the barrel	260 to 270	°C
Temperature in the middle of the barrel	265 to 275	°C
Front temperature of material barrel	265 to 275	°C
Mold temperature	60 to 80	°C

Notes
1. Typical properties: these are not to be construed as specifications.
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

1. Typical properties: these are not to be construed as specifications.

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.