TECHNYL STAR® S 60X1 V30 NATURAL

About
TECHNYL STAR® S 60X1 V30 Natural is a grade based on a non-halogenated flame retardant system and on a patented high flow polyamide 6 resin (TechnylStar), reinforced of 30% of glass fiber, heat stabilized, for injection moulding. This grade is Heat stabilized and provides optimized injection moulding performance.&&

Product Description
Supplier	DOMO
Generic	PA6
Material Status	Commercial: Active
Features	low-temperature impact resistance,Good stripping performance,Halogen free,Arc resistance,Good surface appearance,Corrosion Resistant,High liquidity
Availabilitys	Africa & Middle East ,Europe,Asia Pacific
Process Methods	Injection Molding

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	1.42	g/cm³	ISO 1183
Water Absorption
24 h，23℃	0.9	%	ISO 62
	4.2	%	ISO 62
Molding shrinkage
Parallel, 72 hours, 23 ℃, 50% r. h	0.25	%	ISO 294-4
Normal, 72 hours, 23 ℃, 50% r. h	0.8	%	ISO 294-4

MECHANICAL	Nominal value	Unit	Test method
Tensile Modulus
Dry	11000	MPa	ISO 527
Wet Cond	7200	MPa	ISO 527
Tensile Strength
Broken BRK, dry dry	155	MPa	ISO 527-2
Broken BRK, wet Cond	97	MPa	ISO 527-2
Tensile Strain
Broken BRK, dry dry	2.8	%	ISO 527
Broken BRK, wet Cond	5	%	ISO 527
Flexural Modulus
Dry	9450	MPa	ISO 178
Wet Cond	5400	MPa	ISO 178
Dry	10100	MPa	ASTM D790
Flexural Strength
Dry	248	MPa	ISO 178
Wet Cond	167	MPa	ISO 178
Dry	222	MPa	ASTM D790

IMPACT	Nominal value	Unit	Test method
Charpy Unnotch Impact strength
23 ℃, dry	65	kJ/m²	ISO 179/1eU
23 ℃, moist cond	70	kJ/m²	ISO 179/1eU
-30 ℃, dry	50	kJ/m²	ISO 179/1eU
Charpy Notched Impact Strength
23 ℃, dry	10	kJ/m²	ISO 179/1eA
23 ℃, moist cond	13	kJ/m²	ISO 179/1eA
-30 ℃, dry	9	kJ/m²	ISO 179/1eA
Izod Unnotched Impact strength of cantilever beam
23 ℃, dry	54	KJ/m²	ISO 180/1U
23 ℃, moist cond	63	KJ/m²	ISO 180/1U
Izod Notched Impact strength
23 ℃, dry	10	KJ/m²	ISO 180/1A
23 ℃, moist cond	12	KJ/m²	ISO 180/1A

THERMAL	Nominal value	Unit	Test method
Melting temperature	222	℃	ISO 11357-3
Hot deformation temperature HDT
1.80 MPa	205	℃	ISO 75-1/-2

ELECTRICAL	Nominal value	Unit	Test method
Volume Resistance	1E13	ohm·m	IEC 62631-3-1
Surface Resistivity	6E14	ohm	IEC 62631-3-1
Compared Tracking Index	600	V	IEC 60112
Dielectric Strength	25	kV/mm	IEC 60243-1

FLAME CHARACTERISTICS	Nominal value	Unit	Test method
Flame Class Rating
0.75 mm	V-0		UL 94
1.5 mm	5VA		UL 94
3.0 mm	5VA		UL 94
Glow Wire Flammability Index (GWFI)
0.75 mm	960	℃	IEC 60695-2-12
1.5 mm	960	℃	IEC 60695-2-12
3.0 mm	960	℃	IEC 60695-2-12
Glow Wire Ignitability Temperature (GWIT)
0.75 mm	775	℃	IEC 60695-2-13
1.5 mm	800	℃	IEC 60695-2-13
3.0 mm	825	℃	IEC 60695-2-13
Oxygen Index	35	%	ISO 4589-2

Process Conditions
Injection Molding	Nominal value	Unit	Test method
Drying Temperature	80	℃
Maximum Moisture Content	0.2	%
Rear Temperature Zone 1	230-235	℃
Middle Temperature Zone 2	235-240	℃
Front Temperature Zone 3	240-245	℃
Mold Temperature	60-90	℃

Notes
1. Typical properties: these are not to be construed as specifications.
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

1. Typical properties: these are not to be construed as specifications.

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.