| About |
|---|
| Product Description | |
|---|---|
| Supplier | Chemours |
| Material Status | Commercial: Negative |
| Features | Food contact compliance,Solvent resistance,Quick molding cycle,High Heat Resistance,Low moisture absorption,Weather resistance is good,High ESCR,Good Electrical Properties,Low coefficient of friction,Good flexibility,Good coloring,V-0 |
| Availabilitys | North America,Asia Pacific,Latin America,Europe |
| Process Methods | Injection Molding,Extrusion |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | |||
| — | 2.13 | g/cm³ | ASTM D792 |
| — | 2.13 | g/cm³ | ISO 1183 |
| Melt Flow Rate | |||
| 372℃，5.0kg | 9.0 | g/10min | ASTM D2116 |
| 372℃，5.0kg | 9.0 | g/10min | ISO 12086 |
| Water absorption rate | |||
| 24hr | < 0.010 | % | ASTM D570 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | |||
| Shaw’s D | 56 | ISO 868 | |
| Shaw’s D | 56 | ASTM D2240 | |
| tensile strength | |||
| Yield, 23 ℃ | 28.0 | MPa | ISO 12086 |
| Yield, 23 ℃ | 28.0 | MPa | ASTM D638 |
| Tensile strain | |||
| Fracture, 23 ℃ | 300 | % | ISO 12086 |
| Fracture, 23 ℃ | 300 | % | ASTM D638 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | |||
| 23℃ | No Break | ASTM D256 | |
| 23℃ | No Break | ISO 180 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Continuous use temperature | 205 | ℃ | |
| Melting temperature | 255 | ℃ |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Dielectric strength | |||
| 0.25 mm | > 100 | kV/mm | IEC 60243-1 |
| 0.25 mm | > 100 | kV/mm | ASTM D149 |
| Dielectric constant | ASTM D150 | ||
| 1 kHz | 2.03 | ASTM D150 | |
| 1.00 GHz | 2.03 | ASTM D150 | |
| Relative permittivity | IEC 60250 | ||
| 1 kHz | 2.03 | IEC 60250 | |
| 1.00 GHz | 2.03 | IEC 60250 | |
| Dissipation factor | ASTM D150 | ||
| 1 kHz | 5.0E-5 | ASTM D150 | |
| 1 GHz | 8.0E-4 | ASTM D150 | |
| Dissipation factor | IEC 60250 | ||
| 1 kHz | 5.0E-5 | IEC 60250 | |
| 1 GHz | 8.0E-4 | IEC 60250 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | V-0 | UL 94 | |
| Extreme oxygen index | > 95 | % | ASTM D2863 |
| Extreme oxygen index | > 95 | % | ISO 4589-2 |
| Supplementary information | Nominal value | Unit | Test method |
|---|---|---|---|
| Critical Shear Rate（372℃） | 29.0 | sec^-1 | Internal Method |
| Guide DDR Range（for cable extrusion） | 60.0 to 120 | ||
| MIT flexural strength (film, 200.0 µ m) | 4.0E+4 | Cycles | ASTM D2176 |
| Notes |
|---|
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |