| About |
|---|
| Telcar TL-93-E0847A-92 is a general purpose thermoplastic elastomer designed for the consumer/industrial market. Telcar TL-93-E0847A-92 is a low density, high hardness grade suitable for both injection molding and extrusion.&& |
| Product Description | |
|---|---|
| Supplier | Teknor Apex |
| Generic | TPE |
| Material Status | Commercial: Active |
| Features | Weather resistance is good,Good Hardness,Low density,Moderate liquidity |
| Availabilitys | Africa & Middle East ,North America,Latin America,Asia Pacific,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 0.898 | g/cm³ | ASTM D792 |
| Melt Flow Rate | |||
| 230℃，2.16kg | 9.0 | g/10min | ASTM D1238 |
| elastic body | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | ASTM D412 | ||
| TD, 100% strain | 7.72 | MPa | ASTM D412 |
| MD, 100% strain | 11.0 | MPa | ASTM D412 |
| tensile strength | ASTM D412 | ||
| TD, 300% strain | 8.49 | MPa | ASTM D412 |
| MD, 300% strain | 12.3 | MPa | ASTM D412 |
| tensile strength | ASTM D412 | ||
| fracture | 18.7 | MPa | ASTM D412 |
| MD, fracture | 16.7 | MPa | ASTM D412 |
| Tensile strain | ASTM D412 | ||
| fracture | 720 | % | ASTM D412 |
| Flow rate, fracture | 560 | % | ASTM D412 |
| tear strength | ASTM D624 | ||
| TD | 64.3 | kN/m | ASTM D624 |
| MD | 83.4 | kN/m | ASTM D624 |
| Compression deformation | ASTM D395B | ||
| 23℃，22 hr | 39 | % | ASTM D395B |
| 70℃，22 hr | 66 | % | ASTM D395B |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | ASTM D2240 | ||
| Shore D, 1 second, injection molding | 43 | ASTM D2240 | |
| Shore D, 5 seconds, injection molding | 40 | ASTM D2240 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Extrusion | Nominal value | Unit | Test method |
| Barrel rear temperature | 216 to 238 | °C | |
| Barrel middle temperature | 216 to 238 | °C | |
| Barrel front temperature | 216 to 238 | °C | |
| Nozzle temperature | 216 to 238 | °C | |
| Processing (melt) temperature | 216 to 238 | °C | |
| Mold temperature | 16 to 32 | °C | |
| Injection pressure | 1.38 to 6.89 | MPa | |
| Injection speed | Fast | ||
| Back pressure | 0.172 to 0.862 | MPa | |
| Screw speed | 50 to 120 | rpm | |
| Cushion | 3.81 to 25.4 | mm | |
| Barrel 1 zone temperature | 204 to 227 | °C | |
| Barrel 2 zone temperature | 204 to 227 | °C | |
| Barrel 3 zone temperature | 204 to 227 | °C | |
| Barrel 4 zone temperature | 204 to 227 | °C | |
| Barrel 5 zone temperature | 204 to 227 | °C | |
| Nozzle temperature | 204 to 227 | °C | |
| Notes |
|---|
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |