Tempalux® Medical

About
Medical grade Tempalux is made from Ultem® polyetherimide resin, an amorphous thermoplastic which exhibits excellent resistance to a wide range of chemicals and disinfectants. Ultem maintains its size and shape over a broad temperature range as well as tolerates a high amount of stress over extended periods of time. Recommended sterilization techniques for Tempalux include EtO gas, radiation, steam autoclaving, dry heat and cold sterilization. Applications Include: Provisional trials Instrument handles Medical device components Advantages of Medical Grade Tempalux: Lot controlled and traceable Resin compliant with FDA regulation 21 CFR 177.1595 Resin meets the requirements of USP Class VI specifications Stress relieved&&

About

Medical grade Tempalux is made from Ultem® polyetherimide resin, an amorphous thermoplastic which exhibits excellent resistance to a wide range of chemicals and disinfectants. Ultem maintains its size and shape over a broad temperature range as well as tolerates a high amount of stress over extended periods of time. Recommended sterilization techniques for Tempalux include EtO gas, radiation, steam autoclaving, dry heat and cold sterilization. Applications Include: Provisional trials Instrument handles Medical device components Advantages of Medical Grade Tempalux: Lot controlled and traceable Resin compliant with FDA regulation 21 CFR 177.1595 Resin meets the requirements of USP Class VI specifications Stress relieved&&

Product Description
Supplier	Westlake Plastics
Generic	Polyetherimide
Material Status	Commercial: Active
Features	Steam sterilized,Food contact compliance,High pressure disinfection,Radiation disinfection,Solvent resistance,Ethylene oxide disinfection,Heat sterilization,Amorphous,V-0,5VA
Availabilitys	North America

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	1.27	g/cm³	ASTM D792
Water absorption rate
24hr	0.25	%	ASTM D570

IMPACT	Nominal value	Unit	Test method
Impact strength of cantilever beam notch
23℃	53	J/m	ASTM D256
Notched impact strength of cantilever beam	1300	J/m	ASTM D256

THERMAL	Nominal value	Unit	Test method
Hot deformation temperature			ASTM D648
0.45 MPa, unannealed	210	℃	ASTM D648
1.8 MPa, unannealed	200	℃	ASTM D648
Linear coefficient of thermal expansion
MD	5.6E-5	1/℃	ASTM D696
Thermal conductivity coefficient	0.22	W/m/K	ASTM C177

FLAME CHARACTERISTICS	Nominal value	Test method
Flame retardant level		UL 94
0.41 mm	V-0	UL 94
1.90 mm	5VA	UL 94

MECHANICAL	Nominal value	Unit	Test method
Rockwell hardness
M-level	109		ASTM D785
Tensile modulus	2960	MPa	ASTM D638
tensile strength
yield	105	MPa	ASTM D638
Tensile strain			ASTM D638
yield	7.0	%	ASTM D638
fracture	60	%	ASTM D638
Bending modulus	3310	MPa	ASTM D790
bending strength
yield	152	MPa	ASTM D790
Compression modulus	3310	MPa	ASTM D695
compressive strength	151	MPa	ASTM D695

Notes
1. Typical properties: these are not to be construed as specifications.
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

1. Typical properties: these are not to be construed as specifications.

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.