| About |
|---|
| Texin 4210 resin is a blend of polyester-based polyurethane and polycarbonate. This aromatic grade has a Shore hardness of approximately 70D. It can be processed by injection molding, extrusion, or blow molding.&& |
| Product Description | |
|---|---|
| Supplier | Covestro |
| Generic | PC+TPU |
| Material Status | Commercial: Active |
| Features | Good Rigidity,High impact resistance,Antifreeze |
| Availabilitys | North America |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.21 | g/cm³ | ASTM D792 |
| Density | 1.21 | g/cm³ | ISO 1183 |
| Shrinkage rate | ISO 2577 | ||
| TD：2.54 mm | 0.80 | % | ASTM D955 |
| MD：2.54 mm | 0.80 | % | ASTM D955 |
| TD：2.54 mm | 0.80 | % | ISO 2577 |
| MD：2.54 mm | 0.80 | % | ISO 2577 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | |||
| Shaw’s D | 70 | ISO 868 | |
| Shaw’s D | 70 | ASTM D2240 | |
| Bending modulus | |||
| 23℃ | 700 | MPa | ISO 178 |
| 23℃ | 700 | MPa | ASTM D790 |
| Taber abraser | |||
| 1000 cycles, 1000 g, H-18 wheels | 65.0 | mg | ISO 4649 |
| 1000 cycles, 1000 g, H-18 wheels | 65.0 | mg | ASTM D1044 |
| elastic body | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | |||
| yield | 40.0 | MPa | ASTM D412 |
| yield | 40.0 | MPa | ISO 37 |
| Tensile strain | |||
| fracture | 130 | % | ISO 37 |
| fracture | 130 | % | ASTM D412 |
| tear strength | 158 | kN/m | ASTM D624 |
| tear strength | 160 | kN/m | ISO 34-1 |
| Basho’s elasticity | 45 | % | ASTM D2632 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | ASTM D256 | ||
| -30℃，3.2mm | 53 | J/m | ASTM D256 |
| 23℃，3.2mm | 850 | J/m | ASTM D256 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed | 59.0 | ℃ | ASTM D648 |
| 1.8 MPa, unannealed | 59.0 | ℃ | ISO 75-2/A |
| 0.45 MPa, unannealed | 98.0 | ℃ | ISO 75-2/B |
| 0.45 MPa, unannealed | 98.0 | ℃ | ASTM D648 |
| Embrittlement temperature | < -68.0 | ℃ | ASTM D746 |
| Embrittlement temperature | < -68.0 | ℃ | ISO 974 |
| Glass transition temperature | -35.0 | ℃ | DMA |
| Vicat Softening Temp | 139 | ℃ | ASTM D1525 3 |
| Vicat Softening Temp | 139 | ℃ | ISO 306/50 |
| Linear coefficient of thermal expansion | |||
| MD | 1.0E-4 | 1/℃ | ASTM D696 |
| Supplementary information | Nominal value | Unit | Test method |
|---|---|---|---|
| Compression load | ASTM D575 | ||
| 10% deflection | 31.7 | MPa | ASTM D575 |
| 15% deflection | 41.4 | MPa | ASTM D575 |
| 2% deflection | 3.45 | MPa | ASTM D575 |
| 20% deflection | 56.5 | MPa | ASTM D575 |
| 25% deflection | 68.9 | MPa | ASTM D575 |
| 5% deflection | 13.8 | MPa | ASTM D575 |
| 50% deflection | 130 | MPa | ASTM D575 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Extrusion | Nominal value | Unit | Test method |
| Drying temperature – hot air dryer | 115 to 120 | °C | |
| Drying time – hot air dryer | 2.0 | hr | |
| Recommended maximum moisture content | < 0.030 | % | |
| Recommended injection volume | 40 to 80 | % | |
| Proposed maximum recycled material ratio | 20 | % | |
| Barrel rear temperature | 221 to 232 | °C | |
| Barrel middle temperature | 227 to 238 | °C | |
| Barrel front temperature | 227 to 238 | °C | |
| Nozzle temperature | 227 to 241 | °C | |
| Processing (melt) temperature | 232 to 238 | °C | |
| Mold temperature | 16 to 43 | °C | |
| Injection pressure | 41.4 to 103 | MPa | |
| Injection speed | Slow-Moderate | ||
| Hold pressure | 27.6 to 55.2 | MPa | |
| Back pressure | 0.345 to 1.38 | MPa | |
| Screw speed | 40 to 80 | rpm | |
| Clamping force | 4.1 to 6.9 | kN/cm² | |
| Cushion | < 3.18 | mm | |
| Screw length to diameter ratio | 20.0:1.0 | ||
| Screw compression ratio | 2.5:1.0 to 3.0:1.0 | ||
| Drying temperature | 115 to 120 | °C | |
| Drying time | 2.0 | hr | |
| Barrel 1 zone temperature | 210 to 227 | °C | |
| Barrel 2 zone temperature | 216 to 232 | °C | |
| Barrel 3 zone temperature | 216 to 238 | °C | |
| Melt temperature | 232 to 243 | °C | |
| Nozzle temperature | 221 to 243 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Die C |
| 3. Rate A (50°C/h) |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |